Mode pages for Serial Attached SCSI Protocol (SPL-4) transport protocol:
Disconnect-reconnect (SAS) [dr: 0x2] mode page:
  BITL       [0x04:7:16]  Bus inactivity (time) limit (100us or see BILUNIT)
  MCTL       [0x08:7:16]  Connect time limit (100us or see CTLUNIT)
  MBS        [0x0a:7:16]  Maximum burst size (512 bytes)
  CTLUNIT    [0x0d:3:2 ]  Connect time limit unit
  BILUNIT    [0x0d:1:2 ]  Bus inactivity (time) limit unit
  FBS        [0x0e:7:16]  First burst size (512 bytes)
Protocol specific logical unit (SAS) [pl: 0x18] mode page:
  LUPID      [0x02:3:4 ]  Logical unit's (transport) protocol identifier
  TLR        [0x02:4:1 ]  Transport layer retries
Protocol specific port (SAS) [pp: 0x19] mode page:
  PPID       [0x02:3:4 ]  Port's (transport) protocol identifier
  CAWT       [0x02:6:1 ]  Continue AWT (arbitration wait time (timer))
  BAE        [0x02:5:1 ]  Broadcast asynchronous event
  RLM        [0x02:4:1 ]  Ready LED meaning
  ITNLT      [0x04:7:16]  I_T nexus loss time (ms)
  IRT        [0x06:7:16]  Initiator response timeout (ms)
  RTOL       [0x08:7:16]  Reject to open limit (10 us)
  MAXR       [0x0a:7:8 ]  Maximum allowed xfer ready
Phy control and discover (SAS) [pcd: 0x19,0x1] mode page:
  PPID_1     [0x05:3:4 ]  Port's (transport) protocol identifier
  GENC       [0x06:7:8 ]  Generation code
  NOP        [0x07:7:8 ]  Number of phys
  PHID       [0x09:7:8 ]  Phy identifier
  ADT        [0x0c:6:3 ]  Attached SAS device type
  AREAS      [0x0c:3:4 ]  Attached reason (other end did link reset)
  REAS       [0x0d:7:4 ]  Reason (for starting link reset)
  NLLR       [0x0d:3:4 ]  Negotiated logical link rate
  ASIP       [0x0e:3:1 ]  Attached SSP initiator port
  ATIP       [0x0e:2:1 ]  Attached STP initiator port
  AMIP       [0x0e:1:1 ]  Attached SMP initiator port
  ASTP       [0x0f:3:1 ]  Attached SSP target port
  ATTP       [0x0f:2:1 ]  Attached STP target port
  AMTP       [0x0f:1:1 ]  Attached SMP target port
  SASA       [0x10:7:64]  SAS address
  ASASA      [0x18:7:64]  Attached SAS address
  APHID      [0x20:7:8 ]  Attached phy identifier
  APERCAP    [0x21:7:1 ]  Attached persistent capable
  APOWCAP    [0x21:6:2 ]  Attached power capable
  ASLCAP     [0x21:4:1 ]  Attached slumber capable
  APACAP     [0x21:3:1 ]  Attached partial capable
  AIZPER     [0x21:2:1 ]  Attached inside ZPSDS persistent
  AREQIZ     [0x21:1:1 ]  Attached requested inside ZPSDS
  ABRCAP     [0x21:0:1 ]  Attached break reply capable
  AAPTACAP   [0x22:2:1 ]  Attached APTA capable
  ASMPPCAP   [0x22:1:1 ]  Attached SMP priority capable
  APOWDCAP   [0x22:0:1 ]  Attached power disable capable
  PMILR      [0x28:7:4 ]  Programmed minimum link rate
  HMILR      [0x28:3:4 ]  Hardware minimum link rate
  PMALR      [0x29:7:4 ]  Programmed maximum link rate
  HMALR      [0x29:3:4 ]  Hardware maximum link rate
Shared port control (SAS) [spc: 0x19,0x2] mode page:
  PPID_2     [0x05:3:4 ]  Port's (transport) protocol identifier
  PLT        [0x06:7:16]  Power loss timeout(ms)
  PGRATO     [0x09:7:8 ]  Power grant timeout(sec)
  4PHYS      [0x0a:2:1 ]  4 phy wide port(s) when set
  2PHYS      [0x0a:1:1 ]  2 phy wide port(s) when set
  1PHY       [0x0a:0:1 ]  single phy (narrow) ports
  PMCDT      [0x0b:7:8 ]  port mode change delay time (unit: seconds)
Enhanced phy control (SAS) [sep: 0x19,0x3] mode page:
  PPID_3     [0x05:3:4 ]  Port's (transport) protocol identifier
  GENC_1     [0x06:7:8 ]  Generation code
  NOP_1      [0x07:7:8 ]  Number of phys
  PHID_1     [0x09:7:8 ]  Phy identifier
  PPCAP      [0x0c:7:32]  Programmed phy capabilities
  CPCAP      [0x10:7:32]  Current phy capabilities
  APCAP      [0x14:7:32]  Attached phy capabilities
  OPT_M_EN   [0x1a:5:1 ]  Optical mode enabled
  N_SSC      [0x1a:4:1 ]  Negotiated spread spectrum clocking
  NPLR       [0x1a:3:4 ]  Negotiated physical link rate
  EN_SL      [0x1b:2:1 ]  Enable slumber phy power condition
  EN_PA      [0x1b:1:1 ]  Enable partial phy power condition
  HMS        [0x1b:0:1 ]  Hardware muxing supported
Out of band management control (SAS) [oobm: 0x19,0x4] mode page:
  OOB_RE     [0x04:7:1 ]  Out of band reporting enabled
  OOB_PRV    [0x06:7:16]  Out of band protocol revision code
  OOB_D_ID   [0x08:3:4 ]  Out of band descriptor identifier
  TA_TRE     [0x0c:0:1   0]  Temperature attribute, temperature reporting enabled
  TA_RI      [0x0d:7:8   0]  Temperature attribute, reporting interval (seconds)
  TA_MRI     [0x0e:7:8   0]  Temperature attribute, minimum reporting interval (seconds)
  TA_C_UP    [0x0f:7:4   0]  Temperature attribute, change up (Celsius)
  TA_C_DO    [0x0f:3:4   0]  Temperature attribute, change down (Celsius)
  TA_TM      [0x10:1:2   0]  Temperature attribute, test mode
  TA_TM_T    [0x12:7:8   0]  Temperature attribute test mode temperature