129 lines · plain
1Device tree bindings for NVIDIA Tegra Generic Memory Interface bus2 3The Generic Memory Interface bus enables memory transfers between internal and4external memory. Can be used to attach various high speed devices such as5synchronous/asynchronous NOR, FPGA, UARTS and more.6 7The actual devices are instantiated from the child nodes of a GMI node.8 9Required properties:10 - compatible : Should contain one of the following:11 For Tegra20 must contain "nvidia,tegra20-gmi".12 For Tegra30 must contain "nvidia,tegra30-gmi".13 - reg: Should contain GMI controller registers location and length.14 - clocks: Must contain an entry for each entry in clock-names.15 - clock-names: Must include the following entries: "gmi"16 - resets : Must contain an entry for each entry in reset-names.17 - reset-names : Must include the following entries: "gmi"18 - #address-cells: The number of cells used to represent physical base19 addresses in the GMI address space. Should be 2.20 - #size-cells: The number of cells used to represent the size of an address21 range in the GMI address space. Should be 1.22 - ranges: Must be set up to reflect the memory layout with three integer values23 for each chip-select line in use (only one entry is supported, see below24 comments):25 <cs-number> <offset> <physical address of mapping> <size>26 27Note that the GMI controller does not have any internal chip-select address28decoding, because of that chip-selects either need to be managed via software29or by employing external chip-select decoding logic.30 31If external chip-select logic is used to support multiple devices it is assumed32that the devices use the same timing and so are probably the same type. It also33assumes that they can fit in the 256MB address range. In this case only one34child device is supported which represents the active chip-select line, see35examples for more insight.36 37The chip-select number is decoded from the child nodes second address cell of38'ranges' property, if 'ranges' property is not present or empty chip-select will39then be decoded from the first cell of the 'reg' property.40 41Optional child cs node properties:42 43 - nvidia,snor-data-width-32bit: Use 32bit data-bus, default is 16bit.44 - nvidia,snor-mux-mode: Enable address/data MUX mode.45 - nvidia,snor-rdy-active-before-data: Assert RDY signal one cycle before data.46 If omitted it will be asserted with data.47 - nvidia,snor-rdy-active-high: RDY signal is active high48 - nvidia,snor-adv-active-high: ADV signal is active high49 - nvidia,snor-oe-active-high: WE/OE signal is active high50 - nvidia,snor-cs-active-high: CS signal is active high51 52 Note that there is some special handling for the timing values.53 From Tegra TRM:54 Programming 0 means 1 clock cycle: actual cycle = programmed cycle + 155 56 - nvidia,snor-muxed-width: Number of cycles MUX address/data asserted on the57 bus. Valid values are 0-15, default is 158 - nvidia,snor-hold-width: Number of cycles CE stays asserted after the59 de-assertion of WR_N (in case of SLAVE/MASTER Request) or OE_N60 (in case of MASTER Request). Valid values are 0-15, default is 161 - nvidia,snor-adv-width: Number of cycles during which ADV stays asserted.62 Valid values are 0-15, default is 1.63 - nvidia,snor-ce-width: Number of cycles before CE is asserted.64 Valid values are 0-15, default is 465 - nvidia,snor-we-width: Number of cycles during which WE stays asserted.66 Valid values are 0-15, default is 167 - nvidia,snor-oe-width: Number of cycles during which OE stays asserted.68 Valid values are 0-255, default is 169 - nvidia,snor-wait-width: Number of cycles before READY is asserted.70 Valid values are 0-255, default is 371 72Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the73controllers with a simple-bus node since they are all connected to the same74chip-select (CS4), in this example external address decoding is provided:75 76gmi@70009000 {77 compatible = "nvidia,tegra20-gmi";78 reg = <0x70009000 0x1000>;79 #address-cells = <2>;80 #size-cells = <1>;81 clocks = <&tegra_car TEGRA20_CLK_NOR>;82 clock-names = "gmi";83 resets = <&tegra_car 42>;84 reset-names = "gmi";85 ranges = <4 0 0xd0000000 0xfffffff>;86 87 bus@4,0 {88 compatible = "simple-bus";89 #address-cells = <1>;90 #size-cells = <1>;91 ranges = <0 4 0 0x40100>;92 93 nvidia,snor-mux-mode;94 nvidia,snor-adv-active-high;95 96 can@0 {97 reg = <0 0x100>;98 ...99 };100 101 can@40000 {102 reg = <0x40000 0x100>;103 ...104 };105 };106};107 108Example with one SJA1000 CAN controller connected to the GMI bus109on CS4:110 111gmi@70009000 {112 compatible = "nvidia,tegra20-gmi";113 reg = <0x70009000 0x1000>;114 #address-cells = <2>;115 #size-cells = <1>;116 clocks = <&tegra_car TEGRA20_CLK_NOR>;117 clock-names = "gmi";118 resets = <&tegra_car 42>;119 reset-names = "gmi";120 ranges = <4 0 0xd0000000 0xfffffff>;121 122 can@4,0 {123 reg = <4 0 0x100>;124 nvidia,snor-mux-mode;125 nvidia,snor-adv-active-high;126 ...127 };128};129