270 lines · plain
1TI LMU (Lighting Management Unit) device tree bindings2 3TI LMU driver supports lighting devices below.4 5 Name Child nodes6 ------ ---------------------------------7 LM3631 Backlight and regulator8 LM3632 Backlight and regulator9 LM3633 Backlight, LED and fault monitor10 LM3695 Backlight11 LM36274 Backlight and regulator12 13Required properties:14 - compatible: Should be one of:15 "ti,lm3631"16 "ti,lm3632"17 "ti,lm3633"18 "ti,lm3695"19 "ti,lm36274"20 - reg: I2C slave address.21 0x11 for LM363222 0x29 for LM363123 0x36 for LM363324 0x63 for LM369525 0x11 for LM3627426 27Optional properties:28 - enable-gpios: A GPIO specifier for hardware enable pin.29 - ramp-up-us: Current ramping from one brightness level to30 the a higher brightness level.31 Range from 2048 us - 117.44 s32 - ramp-down-us: Current ramping from one brightness level to33 the a lower brightness level.34 Range from 2048 us - 117.44 s35 - ti,brightness-resolution - This determines whether to use 8 bit brightness36 mode or 11 bit brightness mode. If this value is37 not set the device is defaulted to the preferred38 8bit brightness mode per 7.3.4.1 of the data39 sheet. This setting can either be in the parent40 node or as part of the LED child nodes. This41 is determined by the part itself if the strings42 have a common brightness register or individual43 brightness registers.44 The values are 255 (8bit) or 2047 (11bit).45 46Required node:47 - backlight: All LMU devices have backlight child nodes.48 For the properties, please refer to [1].49 50Optional nodes:51 - fault-monitor: Hardware fault monitoring driver for LM3633 and LM3697.52 Required properties:53 - compatible: Should be one of:54 "ti,lm3633-fault-monitor"55 - leds: LED properties for LM3633. Please refer to [2].56 LED properties for LM36274. Please refer to [4].57 - regulators: Regulator properties for LM3631 and LM3632.58 Please refer to [3].59 60[1] ../leds/backlight/ti-lmu-backlight.txt61[2] ../leds/leds-lm3633.txt62[3] ../regulator/lm363x-regulator.txt63[4] ../leds/leds-lm36274.txt64 65lm3631@29 {66 compatible = "ti,lm3631";67 reg = <0x29>;68 69 regulators {70 compatible = "ti,lm363x-regulator";71 72 vboost {73 regulator-name = "lcd_boost";74 regulator-min-microvolt = <4500000>;75 regulator-max-microvolt = <6350000>;76 regulator-always-on;77 };78 79 vcont {80 regulator-name = "lcd_vcont";81 regulator-min-microvolt = <1800000>;82 regulator-max-microvolt = <3300000>;83 };84 85 voref {86 regulator-name = "lcd_voref";87 regulator-min-microvolt = <4000000>;88 regulator-max-microvolt = <6000000>;89 };90 91 vpos {92 regulator-name = "lcd_vpos";93 regulator-min-microvolt = <4000000>;94 regulator-max-microvolt = <6000000>;95 regulator-boot-on;96 };97 98 vneg {99 regulator-name = "lcd_vneg";100 regulator-min-microvolt = <4000000>;101 regulator-max-microvolt = <6000000>;102 regulator-boot-on;103 };104 };105 106 backlight {107 compatible = "ti,lm3631-backlight";108 109 lcd_bl {110 led-sources = <0 1>;111 ramp-up-us = <300000>;112 };113 };114};115 116lm3632@11 {117 compatible = "ti,lm3632";118 reg = <0x11>;119 120 enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; /* PC2 */121 122 regulators {123 compatible = "ti,lm363x-regulator";124 125 enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,126 <&pioC 1 GPIO_ACTIVE_HIGH>;127 128 vboost {129 regulator-name = "lcd_boost";130 regulator-min-microvolt = <4500000>;131 regulator-max-microvolt = <6400000>;132 regulator-always-on;133 };134 135 vpos {136 regulator-name = "lcd_vpos";137 regulator-min-microvolt = <4000000>;138 regulator-max-microvolt = <6000000>;139 };140 141 vneg {142 regulator-name = "lcd_vneg";143 regulator-min-microvolt = <4000000>;144 regulator-max-microvolt = <6000000>;145 };146 };147 148 backlight {149 compatible = "ti,lm3632-backlight";150 151 pwms = <&pwm0 0 10000 0>; /* pwm number, period, polarity */152 pwm-names = "lmu-backlight";153 154 lcd {155 led-sources = <0 1>;156 pwm-period = <10000>;157 };158 };159};160 161lm3633@36 {162 compatible = "ti,lm3633";163 reg = <0x36>;164 165 enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;166 167 backlight {168 compatible = "ti,lm3633-backlight";169 170 main {171 label = "main_lcd";172 led-sources = <1 2>;173 ramp-up-us = <500000>;174 ramp-down-us = <500000>;175 };176 177 front {178 label = "front_lcd";179 led-sources = <0>;180 ramp-up-us = <1000000>;181 ramp-down-us = <0>;182 };183 };184 185 leds {186 compatible = "ti,lm3633-leds";187 188 chan1 {189 label = "status";190 led-sources = <1>;191 led-max-microamp = <6000>;192 };193 194 chan345 {195 label = "rgb";196 led-sources = <3 4 5>;197 led-max-microamp = <10000>;198 };199 };200 201 fault-monitor {202 compatible = "ti,lm3633-fault-monitor";203 };204};205 206lm3695@63 {207 compatible = "ti,lm3695";208 reg = <0x63>;209 210 enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;211 212 backlight {213 compatible = "ti,lm3695-backlight";214 215 lcd {216 label = "bl";217 led-sources = <0 1>;218 };219 };220};221 222lm36274@11 {223 compatible = "ti,lm36274";224 #address-cells = <1>;225 #size-cells = <0>;226 reg = <0x11>;227 228 enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;229 regulators {230 #address-cells = <1>;231 #size-cells = <0>;232 compatible = "ti,lm363x-regulator";233 234 enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,235 <&pioC 1 GPIO_ACTIVE_HIGH>;236 237 vboost {238 regulator-name = "lcd_boost";239 regulator-min-microvolt = <4000000>;240 regulator-max-microvolt = <7150000>;241 regulator-always-on;242 };243 244 vpos {245 regulator-name = "lcd_vpos";246 regulator-min-microvolt = <4000000>;247 regulator-max-microvolt = <6500000>;248 };249 250 vneg {251 regulator-name = "lcd_vneg";252 regulator-min-microvolt = <4000000>;253 regulator-max-microvolt = <6500000>;254 };255 };256 257 backlight {258 #address-cells = <1>;259 #size-cells = <0>;260 compatible = "ti,lm36274-backlight";261 262 led@0 {263 reg = <0>;264 led-sources = <0 2>;265 label = "white:backlight_cluster";266 linux,default-trigger = "backlight";267 };268 };269};270