205 lines · plain
1Actions Semi S900 Pin Controller2 3This binding describes the pin controller found in the S900 SoC.4 5Required Properties:6 7- compatible: Should be "actions,s900-pinctrl"8- reg: Should contain the register base address and size of9 the pin controller.10- clocks: phandle of the clock feeding the pin controller11- gpio-controller: Marks the device node as a GPIO controller.12- gpio-ranges: Specifies the mapping between gpio controller and13 pin-controller pins.14- #gpio-cells: Should be two. The first cell is the gpio pin number15 and the second cell is used for optional parameters.16- interrupt-controller: Marks the device node as an interrupt controller.17- #interrupt-cells: Specifies the number of cells needed to encode an18 interrupt. Shall be set to 2. The first cell19 defines the interrupt number, the second encodes20 the trigger flags described in21 bindings/interrupt-controller/interrupts.txt22- interrupts: The interrupt outputs from the controller. There is one GPIO23 interrupt per GPIO bank. The number of interrupts listed depends24 on the number of GPIO banks on the SoC. The interrupts must be25 ordered by bank, starting with bank 0.26 27Please refer to pinctrl-bindings.txt in this directory for details of the28common pinctrl bindings used by client devices, including the meaning of the29phrase "pin configuration node".30 31The pin configuration nodes act as a container for an arbitrary number of32subnodes. Each of these subnodes represents some desired configuration for a33pin, a group, or a list of pins or groups. This configuration can include the34mux function to select on those group(s), and various pin configuration35parameters, such as pull-up, drive strength, etc.36 37PIN CONFIGURATION NODES:38 39The name of each subnode is not important; all subnodes should be enumerated40and processed purely based on their content.41 42Each subnode only affects those parameters that are explicitly listed. In43other words, a subnode that lists a mux function but no pin configuration44parameters implies no information about any pin configuration parameters.45Similarly, a pin subnode that describes a pullup parameter implies no46information about e.g. the mux function.47 48Pinmux functions are available only for the pin groups while pinconf49parameters are available for both pin groups and individual pins.50 51The following generic properties as defined in pinctrl-bindings.txt are valid52to specify in a pin configuration subnode:53 54Required Properties:55 56- pins: An array of strings, each string containing the name of a pin.57 These pins are used for selecting the pull control and schmitt58 trigger parameters. The following are the list of pins59 available:60 61 eth_txd0, eth_txd1, eth_txen, eth_rxer, eth_crs_dv,62 eth_rxd1, eth_rxd0, eth_ref_clk, eth_mdc, eth_mdio,63 sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, i2s_lrclk0,64 i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1,65 pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, eram_a5,66 eram_a6, eram_a7, eram_a8, eram_a9, eram_a10, eram_a11,67 lvds_oep, lvds_oen, lvds_odp, lvds_odn, lvds_ocp,68 lvds_ocn, lvds_obp, lvds_obn, lvds_oap, lvds_oan,69 lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp,70 lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean,71 sd0_d0, sd0_d1, sd0_d2, sd0_d3, sd1_d0, sd1_d1,72 sd1_d2, sd1_d3, sd0_cmd, sd0_clk, sd1_cmd, sd1_clk,73 spi0_sclk, spi0_ss, spi0_miso, spi0_mosi, uart0_rx,74 uart0_tx, uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb,75 uart3_rx, uart3_tx, uart3_rtsb, uart3_ctsb, uart4_rx,76 uart4_tx, i2c0_sclk, i2c0_sdata, i2c1_sclk, i2c1_sdata,77 i2c2_sclk, i2c2_sdata, csi0_dn0, csi0_dp0, csi0_dn1,78 csi0_dp1, csi0_cn, csi0_cp, csi0_dn2, csi0_dp2, csi0_dn3,79 csi0_dp3, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp,80 dsi_cn, dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sensor0_pclk,81 csi1_dn0,csi1_dp0,csi1_dn1, csi1_dp1, csi1_cn, csi1_cp,82 sensor0_ckout, nand0_d0, nand0_d1, nand0_d2, nand0_d3,83 nand0_d4, nand0_d5, nand0_d6, nand0_d7, nand0_dqs,84 nand0_dqsn, nand0_ale, nand0_cle, nand0_ceb0, nand0_ceb1,85 nand0_ceb2, nand0_ceb3, nand1_d0, nand1_d1, nand1_d2,86 nand1_d3, nand1_d4, nand1_d5, nand1_d6, nand1_d7, nand1_dqs,87 nand1_dqsn, nand1_ale, nand1_cle, nand1_ceb0, nand1_ceb1,88 nand1_ceb2, nand1_ceb3, sgpio0, sgpio1, sgpio2, sgpio389 90- groups: An array of strings, each string containing the name of a pin91 group. These pin groups are used for selecting the pinmux92 functions.93 94 lvds_oxx_uart4_mfp, rmii_mdc_mfp, rmii_mdio_mfp, sirq0_mfp,95 sirq1_mfp, rmii_txd0_mfp, rmii_txd1_mfp, rmii_txen_mfp,96 rmii_rxer_mfp, rmii_crs_dv_mfp, rmii_rxd1_mfp, rmii_rxd0_mfp,97 rmii_ref_clk_mfp, i2s_d0_mfp, i2s_d1_mfp, i2s_lr_m_clk0_mfp,98 i2s_bclk0_mfp, i2s_bclk1_mclk1_mfp, pcm1_in_out_mfp,99 pcm1_clk_mfp, pcm1_sync_mfp, eram_a5_mfp, eram_a6_mfp,100 eram_a7_mfp, eram_a8_mfp, eram_a9_mfp, eram_a10_mfp,101 eram_a11_mfp, lvds_oep_odn_mfp, lvds_ocp_obn_mfp,102 lvds_oap_oan_mfp, lvds_e_mfp, spi0_sclk_mosi_mfp, spi0_ss_mfp,103 spi0_miso_mfp, uart2_rtsb_mfp, uart2_ctsb_mfp, uart3_rtsb_mfp,104 uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp, sd0_d2_d3_mfp,105 sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_clk_mfp,106 uart0_rx_mfp, nand0_d0_ceb3_mfp, uart0_tx_mfp, i2c0_mfp,107 csi0_cn_cp_mfp, csi0_dn0_dp3_mfp, csi1_dn0_cp_mfp,108 dsi_dp3_dn1_mfp, dsi_cp_dn0_mfp, dsi_dp2_dn2_mfp,109 nand1_d0_ceb1_mfp, nand1_ceb3_mfp, nand1_ceb0_mfp,110 csi1_dn0_dp0_mfp, uart4_rx_tx_mfp111 112 113 These pin groups are used for selecting the drive strength114 parameters.115 116 sgpio3_drv, sgpio2_drv, sgpio1_drv, sgpio0_drv,117 rmii_tx_d0_d1_drv, rmii_txen_rxer_drv, rmii_crs_dv_drv,118 rmii_rx_d1_d0_drv, rmii_ref_clk_drv, rmii_mdc_mdio_drv,119 sirq_0_1_drv, sirq2_drv, i2s_d0_d1_drv, i2s_lr_m_clk0_drv,120 i2s_blk1_mclk1_drv, pcm1_in_out_drv, lvds_oap_oan_drv,121 lvds_oep_odn_drv, lvds_ocp_obn_drv, lvds_e_drv, sd0_d3_d0_drv,122 sd1_d3_d0_drv, sd0_sd1_cmd_clk_drv, spi0_sclk_mosi_drv,123 spi0_ss_miso_drv, uart0_rx_tx_drv, uart4_rx_tx_drv, uart2_drv,124 uart3_drv, i2c0_drv, i2c1_drv, i2c2_drv, sensor0_drv125 126 These pin groups are used for selecting the slew rate127 parameters.128 129 sgpio3_sr, sgpio2_sr, sgpio1_sr, sgpio0_sr, rmii_tx_d0_d1_sr,130 rmii_txen_rxer_sr, rmii_crs_dv_sr, rmii_rx_d1_d0_sr,131 rmii_ref_clk_sr, rmii_mdc_mdio_sr, sirq_0_1_sr, sirq2_sr,132 i2s_do_d1_sr, i2s_lr_m_clk0_sr, i2s_bclk0_mclk1_sr,133 pcm1_in_out_sr, sd1_d3_d0_sr, sd0_sd1_clk_cmd_sr,134 spi0_sclk_mosi_sr, spi0_ss_miso_sr, uart0_rx_tx_sr,135 uart4_rx_tx_sr, uart2_sr, uart3_sr, i2c0_sr, i2c1_sr, i2c2_sr,136 sensor0_sr137 138- function: An array of strings, each string containing the name of the139 pinmux functions. These functions can only be selected by140 the corresponding pin groups. The following are the list of141 pinmux functions available:142 143 eram, eth_rmii, eth_smii, spi0, spi1, spi2, spi3, sens0,144 uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1,145 pcm0, pcm1, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, sd0,146 sd1, sd2, sd3, i2c0, i2c1, i2c2, i2c3, i2c4, i2c5, lvds,147 usb30, usb20, gpu, mipi_csi0, mipi_csi1, mipi_dsi, nand0,148 nand1, spdif, sirq0, sirq1, sirq2149 150Optional Properties:151 152- bias-bus-hold: No arguments. The specified pins should retain the previous153 state value.154- bias-high-impedance: No arguments. The specified pins should be configured155 as high impedance.156- bias-pull-down: No arguments. The specified pins should be configured as157 pull down.158- bias-pull-up: No arguments. The specified pins should be configured as159 pull up.160- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified161 pins162- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified163 pins164- slew-rate: Integer. Sets slew rate for the specified pins.165 Valid values are:166 <0> - Slow167 <1> - Fast168- drive-strength: Integer. Selects the drive strength for the specified169 pins in mA.170 Valid values are:171 <2>172 <4>173 <8>174 <12>175 176Example:177 178 pinctrl: pinctrl@e01b0000 {179 compatible = "actions,s900-pinctrl";180 reg = <0x0 0xe01b0000 0x0 0x1000>;181 clocks = <&cmu CLK_GPIO>;182 gpio-controller;183 gpio-ranges = <&pinctrl 0 0 146>;184 #gpio-cells = <2>;185 interrupt-controller;186 #interrupt-cells = <2>;187 interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,188 <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,189 <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,190 <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,191 <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,192 <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;193 194 uart2-default: uart2-default {195 pinmux {196 groups = "lvds_oep_odn_mfp";197 function = "uart2";198 };199 pinconf {200 groups = "lvds_oep_odn_drv";201 drive-strength = <12>;202 };203 };204 };205