69 lines · plain
1* UCC (Unified Communications Controllers)2 3Required properties:4- device_type : should be "network", "hldc", "uart", "transparent"5 "bisync", "atm", or "serial".6- compatible : could be "ucc_geth" or "fsl_atm" and so on.7- cell-index : the ucc number(1-8), corresponding to UCCx in UM.8- reg : Offset and length of the register set for the device9- interrupts : <a b> where a is the interrupt number and b is a10 field that represents an encoding of the sense and level11 information for the interrupt. This should be encoded based on12 the information in section 2) depending on the type of interrupt13 controller you have.14- pio-handle : The phandle for the Parallel I/O port configuration.15- port-number : for UART drivers, the port number to use, between 0 and 3.16 This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.17 The port number is added to the minor number of the device. Unlike the18 CPM UART driver, the port-number is required for the QE UART driver.19- soft-uart : for UART drivers, if specified this means the QE UART device20 driver should use "Soft-UART" mode, which is needed on some SOCs that have21 broken UART hardware. Soft-UART is provided via a microcode upload.22- rx-clock-name: the UCC receive clock source23 "none": clock source is disabled24 "brg1" through "brg16": clock source is BRG1-BRG16, respectively25 "clk1" through "clk24": clock source is CLK1-CLK24, respectively26- tx-clock-name: the UCC transmit clock source27 "none": clock source is disabled28 "brg1" through "brg16": clock source is BRG1-BRG16, respectively29 "clk1" through "clk24": clock source is CLK1-CLK24, respectively30The following two properties are deprecated. rx-clock has been replaced31with rx-clock-name, and tx-clock has been replaced with tx-clock-name.32Drivers that currently use the deprecated properties should continue to33do so, in order to support older device trees, but they should be updated34to check for the new properties first.35- rx-clock : represents the UCC receive clock source.36 0x00 : clock source is disabled;37 0x1~0x10 : clock source is BRG1~BRG16 respectively;38 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.39- tx-clock: represents the UCC transmit clock source;40 0x00 : clock source is disabled;41 0x1~0x10 : clock source is BRG1~BRG16 respectively;42 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.43 44Required properties for network device_type:45- mac-address : list of bytes representing the ethernet address.46- phy-handle : The phandle for the PHY connected to this controller.47 48Recommended properties:49- phy-connection-type : a string naming the controller/PHY interface type,50 i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal51 Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),52 "tbi", or "rtbi".53 54Example:55 ucc@2000 {56 device_type = "network";57 compatible = "ucc_geth";58 cell-index = <1>;59 reg = <2000 200>;60 interrupts = <a0 0>;61 interrupt-parent = <700>;62 mac-address = [ 00 04 9f 00 23 23 ];63 rx-clock = "none";64 tx-clock = "clk9";65 phy-handle = <212000>;66 phy-connection-type = "gmii";67 pio-handle = <140001>;68 };69