270 lines · yaml
1# SPDX-License-Identifier: GPL-2.0-only2%YAML 1.23---4$id: http://devicetree.org/schemas/soc/qcom/qcom,rpmh-rsc.yaml#5$schema: http://devicetree.org/meta-schemas/core.yaml#6 7title: Qualcomm RPMH RSC8 9maintainers:10 - Bjorn Andersson <bjorn.andersson@linaro.org>11 12description: |13 Resource Power Manager Hardened (RPMH) is the mechanism for communicating14 with the hardened resource accelerators on Qualcomm SoCs. Requests to the15 resources can be written to the Trigger Command Set (TCS) registers and16 using a (addr, val) pair and triggered. Messages in the TCS are then sent in17 sequence over an internal bus.18 19 The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity20 (Resource State Coordinator a.k.a RSC) that can handle multiple sleep and21 active/wake resource requests. Multiple such DRVs can exist in a SoC and can22 be written to from Linux. The structure of each DRV follows the same template23 with a few variations that are captured by the properties here.24 25 A TCS may be triggered from Linux or triggered by the F/W after all the CPUs26 have powered off to facilitate idle power saving. TCS could be classified as::27 ACTIVE - Triggered by Linux28 SLEEP - Triggered by F/W29 WAKE - Triggered by F/W30 CONTROL - Triggered by F/W31 See also:: <dt-bindings/soc/qcom,rpmh-rsc.h>32 33 The order in which they are described in the DT, should match the hardware34 configuration.35 36 Requests can be made for the state of a resource, when the subsystem is37 active or idle. When all subsystems like Modem, GPU, CPU are idle, the38 resource state will be an aggregate of the sleep votes from each of those39 subsystems. Clients may request a sleep value for their shared resources in40 addition to the active mode requests.41 42 Drivers that want to use the RSC to communicate with RPMH must specify their43 bindings as child nodes of the RSC controllers they wish to communicate with.44 45properties:46 compatible:47 const: qcom,rpmh-rsc48 49 interrupts:50 minItems: 151 maxItems: 452 description:53 The interrupt that trips when a message complete/response is received for54 this DRV from the accelerators.55 Number of interrupts must match number of DRV blocks.56 57 label:58 description:59 Name for the RSC. The name would be used in trace logs.60 61 qcom,drv-id:62 $ref: /schemas/types.yaml#/definitions/uint3263 description:64 The ID of the DRV in the RSC block that will be used by this controller.65 66 qcom,tcs-config:67 $ref: /schemas/types.yaml#/definitions/uint32-matrix68 minItems: 469 maxItems: 470 items:71 items:72 - description: |73 TCS type::74 - ACTIVE_TCS75 - SLEEP_TCS76 - WAKE_TCS77 - CONTROL_TCS78 enum: [ 0, 1, 2, 3 ]79 - description: Number of TCS80 description: |81 The tuple defining the configuration of TCS. Must have two cells which82 describe each TCS type. The order of the TCS must match the hardware83 configuration.84 85 qcom,tcs-offset:86 $ref: /schemas/types.yaml#/definitions/uint3287 description:88 The offset of the TCS blocks.89 90 reg:91 minItems: 192 maxItems: 493 94 reg-names:95 minItems: 196 items:97 - const: drv-098 - const: drv-199 - const: drv-2100 - const: drv-3101 102 power-domains:103 maxItems: 1104 105 bcm-voter:106 $ref: /schemas/interconnect/qcom,bcm-voter.yaml#107 108 clock-controller:109 $ref: /schemas/clock/qcom,rpmhcc.yaml#110 111 power-controller:112 $ref: /schemas/power/qcom,rpmpd.yaml#113 114patternProperties:115 '^regulators(-[0-9])?$':116 $ref: /schemas/regulator/qcom,rpmh-regulator.yaml#117 unevaluatedProperties: false118 119required:120 - compatible121 - interrupts122 - qcom,drv-id123 - qcom,tcs-config124 - qcom,tcs-offset125 - reg126 - reg-names127 - power-domains128 129additionalProperties: false130 131examples:132 - |133 // For a TCS whose RSC base address is 0x179C0000 and is at a DRV id of134 // 2, the register offsets for DRV2 start at 0D00, the register135 // calculations are like this::136 // DRV0: 0x179C0000137 // DRV2: 0x179C0000 + 0x10000 = 0x179D0000138 // DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000139 // TCS-OFFSET: 0xD00140 #include <dt-bindings/interrupt-controller/arm-gic.h>141 #include <dt-bindings/soc/qcom,rpmh-rsc.h>142 143 rsc@179c0000 {144 compatible = "qcom,rpmh-rsc";145 reg = <0x179c0000 0x10000>,146 <0x179d0000 0x10000>,147 <0x179e0000 0x10000>;148 reg-names = "drv-0", "drv-1", "drv-2";149 interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,150 <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,151 <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;152 label = "apps_rsc";153 qcom,tcs-offset = <0xd00>;154 qcom,drv-id = <2>;155 qcom,tcs-config = <ACTIVE_TCS 2>,156 <SLEEP_TCS 3>,157 <WAKE_TCS 3>,158 <CONTROL_TCS 1>;159 power-domains = <&CLUSTER_PD>;160 };161 162 - |163 // For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the164 // register offsets for DRV0 start at 01C00, the register calculations are165 // like this::166 // DRV0: 0xAF20000167 // TCS-OFFSET: 0x1C00168 #include <dt-bindings/interrupt-controller/arm-gic.h>169 #include <dt-bindings/soc/qcom,rpmh-rsc.h>170 171 rsc@af20000 {172 compatible = "qcom,rpmh-rsc";173 reg = <0xaf20000 0x10000>;174 reg-names = "drv-0";175 interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;176 label = "disp_rsc";177 qcom,tcs-offset = <0x1c00>;178 qcom,drv-id = <0>;179 qcom,tcs-config = <ACTIVE_TCS 0>,180 <SLEEP_TCS 1>,181 <WAKE_TCS 1>,182 <CONTROL_TCS 0>;183 power-domains = <&CLUSTER_PD>;184 };185 186 - |187 #include <dt-bindings/interrupt-controller/arm-gic.h>188 #include <dt-bindings/soc/qcom,rpmh-rsc.h>189 #include <dt-bindings/power/qcom-rpmpd.h>190 191 rsc@18200000 {192 compatible = "qcom,rpmh-rsc";193 reg = <0x18200000 0x10000>,194 <0x18210000 0x10000>,195 <0x18220000 0x10000>;196 reg-names = "drv-0", "drv-1", "drv-2";197 interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,198 <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,199 <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;200 label = "apps_rsc";201 qcom,tcs-offset = <0xd00>;202 qcom,drv-id = <2>;203 qcom,tcs-config = <ACTIVE_TCS 2>,204 <SLEEP_TCS 3>,205 <WAKE_TCS 3>,206 <CONTROL_TCS 0>;207 power-domains = <&CLUSTER_PD>;208 209 clock-controller {210 compatible = "qcom,sm8350-rpmh-clk";211 #clock-cells = <1>;212 clock-names = "xo";213 clocks = <&xo_board>;214 };215 216 power-controller {217 compatible = "qcom,sm8350-rpmhpd";218 #power-domain-cells = <1>;219 operating-points-v2 = <&rpmhpd_opp_table>;220 221 rpmhpd_opp_table: opp-table {222 compatible = "operating-points-v2";223 224 rpmhpd_opp_ret: opp1 {225 opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;226 };227 228 rpmhpd_opp_min_svs: opp2 {229 opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;230 };231 232 rpmhpd_opp_low_svs: opp3 {233 opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;234 };235 236 rpmhpd_opp_svs: opp4 {237 opp-level = <RPMH_REGULATOR_LEVEL_SVS>;238 };239 240 rpmhpd_opp_svs_l1: opp5 {241 opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;242 };243 244 rpmhpd_opp_nom: opp6 {245 opp-level = <RPMH_REGULATOR_LEVEL_NOM>;246 };247 248 rpmhpd_opp_nom_l1: opp7 {249 opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;250 };251 252 rpmhpd_opp_nom_l2: opp8 {253 opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;254 };255 256 rpmhpd_opp_turbo: opp9 {257 opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;258 };259 260 rpmhpd_opp_turbo_l1: opp10 {261 opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;262 };263 };264 };265 266 bcm-voter {267 compatible = "qcom,bcm-voter";268 };269 };270