188 lines · plain
1=================2MEN Chameleon Bus3=================4 5.. Table of Contents6 =================7 1 Introduction8 1.1 Scope of this Document9 1.2 Limitations of the current implementation10 2 Architecture11 2.1 MEN Chameleon Bus12 2.2 Carrier Devices13 2.3 Parser14 3 Resource handling15 3.1 Memory Resources16 3.2 IRQs17 4 Writing an MCB driver18 4.1 The driver structure19 4.2 Probing and attaching20 4.3 Initializing the driver21 4.4 Using DMA22 23 24Introduction25============26 27This document describes the architecture and implementation of the MEN28Chameleon Bus (called MCB throughout this document).29 30Scope of this Document31----------------------32 33This document is intended to be a short overview of the current34implementation and does by no means describe the complete possibilities of MCB35based devices.36 37Limitations of the current implementation38-----------------------------------------39 40The current implementation is limited to PCI and PCIe based carrier devices41that only use a single memory resource and share the PCI legacy IRQ. Not42implemented are:43 44- Multi-resource MCB devices like the VME Controller or M-Module carrier.45- MCB devices that need another MCB device, like SRAM for a DMA Controller's46 buffer descriptors or a video controller's video memory.47- A per-carrier IRQ domain for carrier devices that have one (or more) IRQs48 per MCB device like PCIe based carriers with MSI or MSI-X support.49 50Architecture51============52 53MCB is divided into 3 functional blocks:54 55- The MEN Chameleon Bus itself,56- drivers for MCB Carrier Devices and57- the parser for the Chameleon table.58 59MEN Chameleon Bus60-----------------61 62The MEN Chameleon Bus is an artificial bus system that attaches to a so63called Chameleon FPGA device found on some hardware produced my MEN Mikro64Elektronik GmbH. These devices are multi-function devices implemented in a65single FPGA and usually attached via some sort of PCI or PCIe link. Each66FPGA contains a header section describing the content of the FPGA. The67header lists the device id, PCI BAR, offset from the beginning of the PCI68BAR, size in the FPGA, interrupt number and some other properties currently69not handled by the MCB implementation.70 71Carrier Devices72---------------73 74A carrier device is just an abstraction for the real world physical bus the75Chameleon FPGA is attached to. Some IP Core drivers may need to interact with76properties of the carrier device (like querying the IRQ number of a PCI77device). To provide abstraction from the real hardware bus, an MCB carrier78device provides callback methods to translate the driver's MCB function calls79to hardware related function calls. For example a carrier device may80implement the get_irq() method which can be translated into a hardware bus81query for the IRQ number the device should use.82 83Parser84------85 86The parser reads the first 512 bytes of a Chameleon device and parses the87Chameleon table. Currently the parser only supports the Chameleon v2 variant88of the Chameleon table but can easily be adopted to support an older or89possible future variant. While parsing the table's entries new MCB devices90are allocated and their resources are assigned according to the resource91assignment in the Chameleon table. After resource assignment is finished, the92MCB devices are registered at the MCB and thus at the driver core of the93Linux kernel.94 95Resource handling96=================97 98The current implementation assigns exactly one memory and one IRQ resource99per MCB device. But this is likely going to change in the future.100 101Memory Resources102----------------103 104Each MCB device has exactly one memory resource, which can be requested from105the MCB bus. This memory resource is the physical address of the MCB device106inside the carrier and is intended to be passed to ioremap() and friends. It107is already requested from the kernel by calling request_mem_region().108 109IRQs110----111 112Each MCB device has exactly one IRQ resource, which can be requested from the113MCB bus. If a carrier device driver implements the ->get_irq() callback114method, the IRQ number assigned by the carrier device will be returned,115otherwise the IRQ number inside the Chameleon table will be returned. This116number is suitable to be passed to request_irq().117 118Writing an MCB driver119=====================120 121The driver structure122--------------------123 124Each MCB driver has a structure to identify the device driver as well as125device ids which identify the IP Core inside the FPGA. The driver structure126also contains callback methods which get executed on driver probe and127removal from the system::128 129 static const struct mcb_device_id foo_ids[] = {130 { .device = 0x123 },131 { }132 };133 MODULE_DEVICE_TABLE(mcb, foo_ids);134 135 static struct mcb_driver foo_driver = {136 driver = {137 .name = "foo-bar",138 .owner = THIS_MODULE,139 },140 .probe = foo_probe,141 .remove = foo_remove,142 .id_table = foo_ids,143 };144 145Probing and attaching146---------------------147 148When a driver is loaded and the MCB devices it services are found, the MCB149core will call the driver's probe callback method. When the driver is removed150from the system, the MCB core will call the driver's remove callback method::151 152 static init foo_probe(struct mcb_device *mdev, const struct mcb_device_id *id);153 static void foo_remove(struct mcb_device *mdev);154 155Initializing the driver156-----------------------157 158When the kernel is booted or your foo driver module is inserted, you have to159perform driver initialization. Usually it is enough to register your driver160module at the MCB core::161 162 static int __init foo_init(void)163 {164 return mcb_register_driver(&foo_driver);165 }166 module_init(foo_init);167 168 static void __exit foo_exit(void)169 {170 mcb_unregister_driver(&foo_driver);171 }172 module_exit(foo_exit);173 174The module_mcb_driver() macro can be used to reduce the above code::175 176 module_mcb_driver(foo_driver);177 178Using DMA179---------180 181To make use of the kernel's DMA-API's function, you will need to use the182carrier device's 'struct device'. Fortunately 'struct mcb_device' embeds a183pointer (->dma_dev) to the carrier's device for DMA purposes::184 185 ret = dma_set_mask_and_coherent(&mdev->dma_dev, DMA_BIT_MASK(dma_bits));186 if (rc)187 /* Handle errors */188