167 lines · plain
1====================2Userspace MAD access3====================4 5Device files6============7 8 Each port of each InfiniBand device has a "umad" device and an9 "issm" device attached. For example, a two-port HCA will have two10 umad devices and two issm devices, while a switch will have one11 device of each type (for switch port 0).12 13Creating MAD agents14===================15 16 A MAD agent can be created by filling in a struct ib_user_mad_reg_req17 and then calling the IB_USER_MAD_REGISTER_AGENT ioctl on a file18 descriptor for the appropriate device file. If the registration19 request succeeds, a 32-bit id will be returned in the structure.20 For example::21 22 struct ib_user_mad_reg_req req = { /* ... */ };23 ret = ioctl(fd, IB_USER_MAD_REGISTER_AGENT, (char *) &req);24 if (!ret)25 my_agent = req.id;26 else27 perror("agent register");28 29 Agents can be unregistered with the IB_USER_MAD_UNREGISTER_AGENT30 ioctl. Also, all agents registered through a file descriptor will31 be unregistered when the descriptor is closed.32 33 201434 a new registration ioctl is now provided which allows additional35 fields to be provided during registration.36 Users of this registration call are implicitly setting the use of37 pkey_index (see below).38 39Receiving MADs40==============41 42 MADs are received using read(). The receive side now supports43 RMPP. The buffer passed to read() must be at least one44 struct ib_user_mad + 256 bytes. For example:45 46 If the buffer passed is not large enough to hold the received47 MAD (RMPP), the errno is set to ENOSPC and the length of the48 buffer needed is set in mad.length.49 50 Example for normal MAD (non RMPP) reads::51 52 struct ib_user_mad *mad;53 mad = malloc(sizeof *mad + 256);54 ret = read(fd, mad, sizeof *mad + 256);55 if (ret != sizeof mad + 256) {56 perror("read");57 free(mad);58 }59 60 Example for RMPP reads::61 62 struct ib_user_mad *mad;63 mad = malloc(sizeof *mad + 256);64 ret = read(fd, mad, sizeof *mad + 256);65 if (ret == -ENOSPC)) {66 length = mad.length;67 free(mad);68 mad = malloc(sizeof *mad + length);69 ret = read(fd, mad, sizeof *mad + length);70 }71 if (ret < 0) {72 perror("read");73 free(mad);74 }75 76 In addition to the actual MAD contents, the other struct ib_user_mad77 fields will be filled in with information on the received MAD. For78 example, the remote LID will be in mad.lid.79 80 If a send times out, a receive will be generated with mad.status set81 to ETIMEDOUT. Otherwise when a MAD has been successfully received,82 mad.status will be 0.83 84 poll()/select() may be used to wait until a MAD can be read.85 86Sending MADs87============88 89 MADs are sent using write(). The agent ID for sending should be90 filled into the id field of the MAD, the destination LID should be91 filled into the lid field, and so on. The send side does support92 RMPP so arbitrary length MAD can be sent. For example::93 94 struct ib_user_mad *mad;95 96 mad = malloc(sizeof *mad + mad_length);97 98 /* fill in mad->data */99 100 mad->hdr.id = my_agent; /* req.id from agent registration */101 mad->hdr.lid = my_dest; /* in network byte order... */102 /* etc. */103 104 ret = write(fd, &mad, sizeof *mad + mad_length);105 if (ret != sizeof *mad + mad_length)106 perror("write");107 108Transaction IDs109===============110 111 Users of the umad devices can use the lower 32 bits of the112 transaction ID field (that is, the least significant half of the113 field in network byte order) in MADs being sent to match114 request/response pairs. The upper 32 bits are reserved for use by115 the kernel and will be overwritten before a MAD is sent.116 117P_Key Index Handling118====================119 120 The old ib_umad interface did not allow setting the P_Key index for121 MADs that are sent and did not provide a way for obtaining the P_Key122 index of received MADs. A new layout for struct ib_user_mad_hdr123 with a pkey_index member has been defined; however, to preserve binary124 compatibility with older applications, this new layout will not be used125 unless one of IB_USER_MAD_ENABLE_PKEY or IB_USER_MAD_REGISTER_AGENT2 ioctl's126 are called before a file descriptor is used for anything else.127 128 In September 2008, the IB_USER_MAD_ABI_VERSION will be incremented129 to 6, the new layout of struct ib_user_mad_hdr will be used by130 default, and the IB_USER_MAD_ENABLE_PKEY ioctl will be removed.131 132Setting IsSM Capability Bit133===========================134 135 To set the IsSM capability bit for a port, simply open the136 corresponding issm device file. If the IsSM bit is already set,137 then the open call will block until the bit is cleared (or return138 immediately with errno set to EAGAIN if the O_NONBLOCK flag is139 passed to open()). The IsSM bit will be cleared when the issm file140 is closed. No read, write or other operations can be performed on141 the issm file.142 143/dev files144==========145 146 To create the appropriate character device files automatically with147 udev, a rule like::148 149 KERNEL=="umad*", NAME="infiniband/%k"150 KERNEL=="issm*", NAME="infiniband/%k"151 152 can be used. This will create device nodes named::153 154 /dev/infiniband/umad0155 /dev/infiniband/issm0156 157 for the first port, and so on. The InfiniBand device and port158 associated with these devices can be determined from the files::159 160 /sys/class/infiniband_mad/umad0/ibdev161 /sys/class/infiniband_mad/umad0/port162 163 and::164 165 /sys/class/infiniband_mad/issm0/ibdev166 /sys/class/infiniband_mad/issm0/port167