141 lines · plain
1.. SPDX-License-Identifier: GPL-2.02 3=====================4TLAN driver for Linux5=====================6 7:Version: 1.14a8 9(C) 1997-1998 Caldera, Inc.10 11(C) 1998 James Banks12 13(C) 1999-2001 Torben Mathiasen <tmm@image.dk, torben.mathiasen@compaq.com>14 15For driver information/updates visit http://www.compaq.com16 17 18 19 20 21I. Supported Devices22====================23 24 Only PCI devices will work with this driver.25 26 Supported:27 28 ========= ========= ===========================================29 Vendor ID Device ID Name30 ========= ========= ===========================================31 0e11 ae32 Compaq Netelligent 10/100 TX PCI UTP32 0e11 ae34 Compaq Netelligent 10 T PCI UTP33 0e11 ae35 Compaq Integrated NetFlex 3/P34 0e11 ae40 Compaq Netelligent Dual 10/100 TX PCI UTP35 0e11 ae43 Compaq Netelligent Integrated 10/100 TX UTP36 0e11 b011 Compaq Netelligent 10/100 TX Embedded UTP37 0e11 b012 Compaq Netelligent 10 T/2 PCI UTP/Coax38 0e11 b030 Compaq Netelligent 10/100 TX UTP39 0e11 f130 Compaq NetFlex 3/P40 0e11 f150 Compaq NetFlex 3/P41 108d 0012 Olicom OC-232542 108d 0013 Olicom OC-218343 108d 0014 Olicom OC-232644 ========= ========= ===========================================45 46 47 Caveats:48 49 I am not sure if 100BaseTX daughterboards (for those cards which50 support such things) will work. I haven't had any solid evidence51 either way.52 53 However, if a card supports 100BaseTx without requiring an add54 on daughterboard, it should work with 100BaseTx.55 56 The "Netelligent 10 T/2 PCI UTP/Coax" (b012) device is untested,57 but I do not expect any problems.58 59 60II. Driver Options61==================62 63 1. You can append debug=x to the end of the insmod line to get64 debug messages, where x is a bit field where the bits mean65 the following:66 67 ==== =====================================68 0x01 Turn on general debugging messages.69 0x02 Turn on receive debugging messages.70 0x04 Turn on transmit debugging messages.71 0x08 Turn on list debugging messages.72 ==== =====================================73 74 2. You can append aui=1 to the end of the insmod line to cause75 the adapter to use the AUI interface instead of the 10 Base T76 interface. This is also what to do if you want to use the BNC77 connector on a TLAN based device. (Setting this option on a78 device that does not have an AUI/BNC connector will probably79 cause it to not function correctly.)80 81 3. You can set duplex=1 to force half duplex, and duplex=2 to82 force full duplex.83 84 4. You can set speed=10 to force 10Mbs operation, and speed=10085 to force 100Mbs operation. (I'm not sure what will happen86 if a card which only supports 10Mbs is forced into 100Mbs87 mode.)88 89 5. You have to use speed=X duplex=Y together now. If you just90 do "insmod tlan.o speed=100" the driver will do Auto-Neg.91 To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=1092 duplex=1".93 94 6. If the driver is built into the kernel, you can use the 3rd95 and 4th parameters to set aui and debug respectively. For96 example::97 98 ether=0,0,0x1,0x7,eth099 100 This sets aui to 0x1 and debug to 0x7, assuming eth0 is a101 supported TLAN device.102 103 The bits in the third byte are assigned as follows:104 105 ==== ===============106 0x01 aui107 0x02 use half duplex108 0x04 use full duplex109 0x08 use 10BaseT110 0x10 use 100BaseTx111 ==== ===============112 113 You also need to set both speed and duplex settings when forcing114 speeds with kernel-parameters.115 ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex.116 117 7. If you have more than one tlan adapter in your system, you can118 use the above options on a per adapter basis. To force a 100Mbit/HD119 link with your eth1 adapter use::120 121 insmod tlan speed=0,100 duplex=0,1122 123 Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD.124 Note that the tlan driver supports a maximum of 8 adapters.125 126 127III. Things to try if you have problems128=======================================129 130 1. Make sure your card's PCI id is among those listed in131 section I, above.132 2. Make sure routing is correct.133 3. Try forcing different speed/duplex settings134 135 136There is also a tlan mailing list which you can join by sending "subscribe tlan"137in the body of an email to majordomo@vuser.vu.union.edu.138 139There is also a tlan website at http://www.compaq.com140 141