299 lines · c
1// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.02/*******************************************************************************3 *4 * Module Name: utresdecode - Resource descriptor keyword strings5 *6 ******************************************************************************/7 8#include <acpi/acpi.h>9#include "accommon.h"10#include "acresrc.h"11 12#define _COMPONENT ACPI_UTILITIES13ACPI_MODULE_NAME("utresdecode")14 15#if defined (ACPI_DEBUG_OUTPUT) || \16 defined (ACPI_DISASSEMBLER) || \17 defined (ACPI_DEBUGGER)18/*19 * Strings used to decode resource descriptors.20 * Used by both the disassembler and the debugger resource dump routines21 */22const char *acpi_gbl_bm_decode[] = {23 "NotBusMaster",24 "BusMaster"25};26 27const char *acpi_gbl_config_decode[] = {28 "0 - Good Configuration",29 "1 - Acceptable Configuration",30 "2 - Suboptimal Configuration",31 "3 - ***Invalid Configuration***",32};33 34const char *acpi_gbl_consume_decode[] = {35 "ResourceProducer",36 "ResourceConsumer"37};38 39const char *acpi_gbl_dec_decode[] = {40 "PosDecode",41 "SubDecode"42};43 44const char *acpi_gbl_he_decode[] = {45 "Level",46 "Edge"47};48 49const char *acpi_gbl_io_decode[] = {50 "Decode10",51 "Decode16"52};53 54const char *acpi_gbl_ll_decode[] = {55 "ActiveHigh",56 "ActiveLow",57 "ActiveBoth",58 "Reserved"59};60 61const char *acpi_gbl_max_decode[] = {62 "MaxNotFixed",63 "MaxFixed"64};65 66const char *acpi_gbl_mem_decode[] = {67 "NonCacheable",68 "Cacheable",69 "WriteCombining",70 "Prefetchable"71};72 73const char *acpi_gbl_min_decode[] = {74 "MinNotFixed",75 "MinFixed"76};77 78const char *acpi_gbl_mtp_decode[] = {79 "AddressRangeMemory",80 "AddressRangeReserved",81 "AddressRangeACPI",82 "AddressRangeNVS"83};84 85const char *acpi_gbl_phy_decode[] = {86 "Type C",87 "Type D",88 "Unknown Type",89 "Unknown Type"90};91 92const char *acpi_gbl_rng_decode[] = {93 "InvalidRanges",94 "NonISAOnlyRanges",95 "ISAOnlyRanges",96 "EntireRange"97};98 99const char *acpi_gbl_rw_decode[] = {100 "ReadOnly",101 "ReadWrite"102};103 104const char *acpi_gbl_shr_decode[] = {105 "Exclusive",106 "Shared",107 "ExclusiveAndWake", /* ACPI 5.0 */108 "SharedAndWake" /* ACPI 5.0 */109};110 111const char *acpi_gbl_siz_decode[] = {112 "Transfer8",113 "Transfer8_16",114 "Transfer16",115 "InvalidSize"116};117 118const char *acpi_gbl_trs_decode[] = {119 "DenseTranslation",120 "SparseTranslation"121};122 123const char *acpi_gbl_ttp_decode[] = {124 "TypeStatic",125 "TypeTranslation"126};127 128const char *acpi_gbl_typ_decode[] = {129 "Compatibility",130 "TypeA",131 "TypeB",132 "TypeF"133};134 135const char *acpi_gbl_ppc_decode[] = {136 "PullDefault",137 "PullUp",138 "PullDown",139 "PullNone"140};141 142const char *acpi_gbl_ior_decode[] = {143 "IoRestrictionNone",144 "IoRestrictionInputOnly",145 "IoRestrictionOutputOnly",146 "IoRestrictionNoneAndPreserve"147};148 149const char *acpi_gbl_dts_decode[] = {150 "Width8bit",151 "Width16bit",152 "Width32bit",153 "Width64bit",154 "Width128bit",155 "Width256bit",156};157 158/* GPIO connection type */159 160const char *acpi_gbl_ct_decode[] = {161 "Interrupt",162 "I/O"163};164 165/* Serial bus type */166 167const char *acpi_gbl_sbt_decode[] = {168 "/* UNKNOWN serial bus type */",169 "I2C",170 "SPI",171 "UART",172 "CSI2"173};174 175/* I2C serial bus access mode */176 177const char *acpi_gbl_am_decode[] = {178 "AddressingMode7Bit",179 "AddressingMode10Bit"180};181 182/* I2C serial bus slave mode */183 184const char *acpi_gbl_sm_decode[] = {185 "ControllerInitiated",186 "DeviceInitiated"187};188 189/* SPI serial bus wire mode */190 191const char *acpi_gbl_wm_decode[] = {192 "FourWireMode",193 "ThreeWireMode"194};195 196/* SPI serial clock phase */197 198const char *acpi_gbl_cph_decode[] = {199 "ClockPhaseFirst",200 "ClockPhaseSecond"201};202 203/* SPI serial bus clock polarity */204 205const char *acpi_gbl_cpo_decode[] = {206 "ClockPolarityLow",207 "ClockPolarityHigh"208};209 210/* SPI serial bus device polarity */211 212const char *acpi_gbl_dp_decode[] = {213 "PolarityLow",214 "PolarityHigh"215};216 217/* UART serial bus endian */218 219const char *acpi_gbl_ed_decode[] = {220 "LittleEndian",221 "BigEndian"222};223 224/* UART serial bus bits per byte */225 226const char *acpi_gbl_bpb_decode[] = {227 "DataBitsFive",228 "DataBitsSix",229 "DataBitsSeven",230 "DataBitsEight",231 "DataBitsNine",232 "/* UNKNOWN Bits per byte */",233 "/* UNKNOWN Bits per byte */",234 "/* UNKNOWN Bits per byte */"235};236 237/* UART serial bus stop bits */238 239const char *acpi_gbl_sb_decode[] = {240 "StopBitsZero",241 "StopBitsOne",242 "StopBitsOnePlusHalf",243 "StopBitsTwo"244};245 246/* UART serial bus flow control */247 248const char *acpi_gbl_fc_decode[] = {249 "FlowControlNone",250 "FlowControlHardware",251 "FlowControlXON",252 "/* UNKNOWN flow control keyword */"253};254 255/* UART serial bus parity type */256 257const char *acpi_gbl_pt_decode[] = {258 "ParityTypeNone",259 "ParityTypeEven",260 "ParityTypeOdd",261 "ParityTypeMark",262 "ParityTypeSpace",263 "/* UNKNOWN parity keyword */",264 "/* UNKNOWN parity keyword */",265 "/* UNKNOWN parity keyword */"266};267 268/* pin_config type */269 270const char *acpi_gbl_ptyp_decode[] = {271 "Default",272 "Bias Pull-up",273 "Bias Pull-down",274 "Bias Default",275 "Bias Disable",276 "Bias High Impedance",277 "Bias Bus Hold",278 "Drive Open Drain",279 "Drive Open Source",280 "Drive Push Pull",281 "Drive Strength",282 "Slew Rate",283 "Input Debounce",284 "Input Schmitt Trigger",285};286 287const char *acpi_gbl_clock_input_mode[] = {288 "Fixed",289 "Variable",290};291 292const char *acpi_gbl_clock_input_scale[] = {293 "Hz",294 "KHz",295 "MHz",296};297 298#endif299