1033 lines · c
1// SPDX-License-Identifier: GPL-2.0-only2/*3 * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers.4 *5 * This driver is heavily based upon:6 *7 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 20038 *9 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>10 * Portions Copyright (C) 2001 Sun Microsystems, Inc.11 * Portions Copyright (C) 2003 Red Hat Inc12 * Portions Copyright (C) 2005-2010 MontaVista Software, Inc.13 *14 * TODO15 * Look into engine reset on timeout errors. Should not be required.16 */17#include <linux/kernel.h>18#include <linux/module.h>19#include <linux/pci.h>20#include <linux/blkdev.h>21#include <linux/delay.h>22#include <scsi/scsi_host.h>23#include <linux/libata.h>24 25#define DRV_NAME "pata_hpt37x"26#define DRV_VERSION "0.6.30"27 28struct hpt_clock {29 u8 xfer_speed;30 u32 timing;31};32 33struct hpt_chip {34 const char *name;35 unsigned int base;36 struct hpt_clock const *clocks[4];37};38 39/* key for bus clock timings40 * bit41 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.42 * cycles = value + 143 * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.44 * cycles = value + 145 * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file46 * register access.47 * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file48 * register access.49 * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.50 * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.51 * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.52 * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file53 * register access.54 * 28 UDMA enable.55 * 29 DMA enable.56 * 30 PIO_MST enable. If set, the chip is in bus master mode during57 * PIO xfer.58 * 31 FIFO enable. Only for PIO.59 */60 61static struct hpt_clock hpt37x_timings_33[] = {62 { XFER_UDMA_6, 0x12446231 }, /* 0x12646231 ?? */63 { XFER_UDMA_5, 0x12446231 },64 { XFER_UDMA_4, 0x12446231 },65 { XFER_UDMA_3, 0x126c6231 },66 { XFER_UDMA_2, 0x12486231 },67 { XFER_UDMA_1, 0x124c6233 },68 { XFER_UDMA_0, 0x12506297 },69 70 { XFER_MW_DMA_2, 0x22406c31 },71 { XFER_MW_DMA_1, 0x22406c33 },72 { XFER_MW_DMA_0, 0x22406c97 },73 74 { XFER_PIO_4, 0x06414e31 },75 { XFER_PIO_3, 0x06414e42 },76 { XFER_PIO_2, 0x06414e53 },77 { XFER_PIO_1, 0x06814e93 },78 { XFER_PIO_0, 0x06814ea7 }79};80 81static struct hpt_clock hpt37x_timings_50[] = {82 { XFER_UDMA_6, 0x12848242 },83 { XFER_UDMA_5, 0x12848242 },84 { XFER_UDMA_4, 0x12ac8242 },85 { XFER_UDMA_3, 0x128c8242 },86 { XFER_UDMA_2, 0x120c8242 },87 { XFER_UDMA_1, 0x12148254 },88 { XFER_UDMA_0, 0x121882ea },89 90 { XFER_MW_DMA_2, 0x22808242 },91 { XFER_MW_DMA_1, 0x22808254 },92 { XFER_MW_DMA_0, 0x228082ea },93 94 { XFER_PIO_4, 0x0a81f442 },95 { XFER_PIO_3, 0x0a81f443 },96 { XFER_PIO_2, 0x0a81f454 },97 { XFER_PIO_1, 0x0ac1f465 },98 { XFER_PIO_0, 0x0ac1f48a }99};100 101static struct hpt_clock hpt37x_timings_66[] = {102 { XFER_UDMA_6, 0x1c869c62 },103 { XFER_UDMA_5, 0x1cae9c62 }, /* 0x1c8a9c62 */104 { XFER_UDMA_4, 0x1c8a9c62 },105 { XFER_UDMA_3, 0x1c8e9c62 },106 { XFER_UDMA_2, 0x1c929c62 },107 { XFER_UDMA_1, 0x1c9a9c62 },108 { XFER_UDMA_0, 0x1c829c62 },109 110 { XFER_MW_DMA_2, 0x2c829c62 },111 { XFER_MW_DMA_1, 0x2c829c66 },112 { XFER_MW_DMA_0, 0x2c829d2e },113 114 { XFER_PIO_4, 0x0c829c62 },115 { XFER_PIO_3, 0x0c829c84 },116 { XFER_PIO_2, 0x0c829ca6 },117 { XFER_PIO_1, 0x0d029d26 },118 { XFER_PIO_0, 0x0d029d5e }119};120 121 122static const struct hpt_chip hpt370 = {123 "HPT370",124 48,125 {126 hpt37x_timings_33,127 NULL,128 NULL,129 NULL130 }131};132 133static const struct hpt_chip hpt370a = {134 "HPT370A",135 48,136 {137 hpt37x_timings_33,138 NULL,139 hpt37x_timings_50,140 NULL141 }142};143 144static const struct hpt_chip hpt372 = {145 "HPT372",146 55,147 {148 hpt37x_timings_33,149 NULL,150 hpt37x_timings_50,151 hpt37x_timings_66152 }153};154 155static const struct hpt_chip hpt302 = {156 "HPT302",157 66,158 {159 hpt37x_timings_33,160 NULL,161 hpt37x_timings_50,162 hpt37x_timings_66163 }164};165 166static const struct hpt_chip hpt371 = {167 "HPT371",168 66,169 {170 hpt37x_timings_33,171 NULL,172 hpt37x_timings_50,173 hpt37x_timings_66174 }175};176 177static const struct hpt_chip hpt372a = {178 "HPT372A",179 66,180 {181 hpt37x_timings_33,182 NULL,183 hpt37x_timings_50,184 hpt37x_timings_66185 }186};187 188static const struct hpt_chip hpt374 = {189 "HPT374",190 48,191 {192 hpt37x_timings_33,193 NULL,194 NULL,195 NULL196 }197};198 199/**200 * hpt37x_find_mode - reset the hpt37x bus201 * @ap: ATA port202 * @speed: transfer mode203 *204 * Return the 32bit register programming information for this channel205 * that matches the speed provided.206 */207 208static u32 hpt37x_find_mode(struct ata_port *ap, int speed)209{210 struct hpt_clock *clocks = ap->host->private_data;211 212 while (clocks->xfer_speed) {213 if (clocks->xfer_speed == speed)214 return clocks->timing;215 clocks++;216 }217 BUG();218 return 0xffffffffU; /* silence compiler warning */219}220 221static int hpt_dma_broken(const struct ata_device *dev, char *modestr,222 const char * const list[])223{224 unsigned char model_num[ATA_ID_PROD_LEN + 1];225 int i;226 227 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));228 229 i = match_string(list, -1, model_num);230 if (i >= 0) {231 ata_dev_warn(dev, "%s is not supported for %s\n",232 modestr, list[i]);233 return 1;234 }235 return 0;236}237 238static const char * const bad_ata33[] = {239 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3",240 "Maxtor 90845U3", "Maxtor 90650U2",241 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5",242 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",243 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6",244 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",245 "Maxtor 90510D4",246 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",247 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7",248 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",249 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5",250 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",251 NULL252};253 254static const char * const bad_ata100_5[] = {255 "IBM-DTLA-307075",256 "IBM-DTLA-307060",257 "IBM-DTLA-307045",258 "IBM-DTLA-307030",259 "IBM-DTLA-307020",260 "IBM-DTLA-307015",261 "IBM-DTLA-305040",262 "IBM-DTLA-305030",263 "IBM-DTLA-305020",264 "IC35L010AVER07-0",265 "IC35L020AVER07-0",266 "IC35L030AVER07-0",267 "IC35L040AVER07-0",268 "IC35L060AVER07-0",269 "WDC AC310200R",270 NULL271};272 273/**274 * hpt370_filter - mode selection filter275 * @adev: ATA device276 * @mask: mode mask277 *278 * Block UDMA on devices that cause trouble with this controller.279 */280 281static unsigned int hpt370_filter(struct ata_device *adev, unsigned int mask)282{283 if (adev->class == ATA_DEV_ATA) {284 if (hpt_dma_broken(adev, "UDMA", bad_ata33))285 mask &= ~ATA_MASK_UDMA;286 if (hpt_dma_broken(adev, "UDMA100", bad_ata100_5))287 mask &= ~(0xE0 << ATA_SHIFT_UDMA);288 }289 return mask;290}291 292/**293 * hpt370a_filter - mode selection filter294 * @adev: ATA device295 * @mask: mode mask296 *297 * Block UDMA on devices that cause trouble with this controller.298 */299 300static unsigned int hpt370a_filter(struct ata_device *adev, unsigned int mask)301{302 if (adev->class == ATA_DEV_ATA) {303 if (hpt_dma_broken(adev, "UDMA100", bad_ata100_5))304 mask &= ~(0xE0 << ATA_SHIFT_UDMA);305 }306 return mask;307}308 309/**310 * hpt372_filter - mode selection filter311 * @adev: ATA device312 * @mask: mode mask313 *314 * The Marvell bridge chips used on the HighPoint SATA cards do not seem315 * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...316 */317static unsigned int hpt372_filter(struct ata_device *adev, unsigned int mask)318{319 if (ata_id_is_sata(adev->id))320 mask &= ~((0xE << ATA_SHIFT_UDMA) | ATA_MASK_MWDMA);321 322 return mask;323}324 325/**326 * hpt37x_cable_detect - Detect the cable type327 * @ap: ATA port to detect on328 *329 * Return the cable type attached to this port330 */331 332static int hpt37x_cable_detect(struct ata_port *ap)333{334 struct pci_dev *pdev = to_pci_dev(ap->host->dev);335 u8 scr2, ata66;336 337 pci_read_config_byte(pdev, 0x5B, &scr2);338 pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);339 340 udelay(10); /* debounce */341 342 /* Cable register now active */343 pci_read_config_byte(pdev, 0x5A, &ata66);344 /* Restore state */345 pci_write_config_byte(pdev, 0x5B, scr2);346 347 if (ata66 & (2 >> ap->port_no))348 return ATA_CBL_PATA40;349 else350 return ATA_CBL_PATA80;351}352 353/**354 * hpt374_fn1_cable_detect - Detect the cable type355 * @ap: ATA port to detect on356 *357 * Return the cable type attached to this port358 */359 360static int hpt374_fn1_cable_detect(struct ata_port *ap)361{362 struct pci_dev *pdev = to_pci_dev(ap->host->dev);363 unsigned int mcrbase = 0x50 + 4 * ap->port_no;364 u16 mcr3;365 u8 ata66;366 367 /* Do the extra channel work */368 pci_read_config_word(pdev, mcrbase + 2, &mcr3);369 /* Set bit 15 of 0x52 to enable TCBLID as input */370 pci_write_config_word(pdev, mcrbase + 2, mcr3 | 0x8000);371 pci_read_config_byte(pdev, 0x5A, &ata66);372 /* Reset TCBLID/FCBLID to output */373 pci_write_config_word(pdev, mcrbase + 2, mcr3);374 375 if (ata66 & (2 >> ap->port_no))376 return ATA_CBL_PATA40;377 else378 return ATA_CBL_PATA80;379}380 381/**382 * hpt37x_pre_reset - reset the hpt37x bus383 * @link: ATA link to reset384 * @deadline: deadline jiffies for the operation385 *386 * Perform the initial reset handling for the HPT37x.387 */388 389static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)390{391 struct ata_port *ap = link->ap;392 struct pci_dev *pdev = to_pci_dev(ap->host->dev);393 static const struct pci_bits hpt37x_enable_bits[] = {394 { 0x50, 1, 0x04, 0x04 },395 { 0x54, 1, 0x04, 0x04 }396 };397 u8 mcr2;398 399 if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))400 return -ENOENT;401 402 /* Reset the state machine */403 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);404 udelay(100);405 406 /*407 * Disable the "fast interrupt" prediction. Don't hold off408 * on interrupts. (== 0x01 despite what the docs say)409 */410 pci_read_config_byte(pdev, 0x51 + 4 * ap->port_no, &mcr2);411 /* Is it HPT370/A? */412 if (pdev->device == PCI_DEVICE_ID_TTI_HPT366 && pdev->revision < 5) {413 mcr2 &= ~0x02;414 mcr2 |= 0x01;415 } else {416 mcr2 &= ~0x07;417 }418 pci_write_config_byte(pdev, 0x51 + 4 * ap->port_no, mcr2);419 420 return ata_sff_prereset(link, deadline);421}422 423static void hpt37x_set_mode(struct ata_port *ap, struct ata_device *adev,424 u8 mode)425{426 struct pci_dev *pdev = to_pci_dev(ap->host->dev);427 int addr = 0x40 + 4 * (adev->devno + 2 * ap->port_no);428 u32 reg, timing, mask;429 430 /* Determine timing mask and find matching mode entry */431 if (mode < XFER_MW_DMA_0)432 mask = 0xcfc3ffff;433 else if (mode < XFER_UDMA_0)434 mask = 0x31c001ff;435 else436 mask = 0x303c0000;437 438 timing = hpt37x_find_mode(ap, mode);439 440 pci_read_config_dword(pdev, addr, ®);441 reg = (reg & ~mask) | (timing & mask);442 pci_write_config_dword(pdev, addr, reg);443}444/**445 * hpt37x_set_piomode - PIO setup446 * @ap: ATA interface447 * @adev: device on the interface448 *449 * Perform PIO mode setup.450 */451 452static void hpt37x_set_piomode(struct ata_port *ap, struct ata_device *adev)453{454 hpt37x_set_mode(ap, adev, adev->pio_mode);455}456 457/**458 * hpt37x_set_dmamode - DMA timing setup459 * @ap: ATA interface460 * @adev: Device being configured461 *462 * Set up the channel for MWDMA or UDMA modes.463 */464 465static void hpt37x_set_dmamode(struct ata_port *ap, struct ata_device *adev)466{467 hpt37x_set_mode(ap, adev, adev->dma_mode);468}469 470/**471 * hpt370_bmdma_stop - DMA engine stop472 * @qc: ATA command473 *474 * Work around the HPT370 DMA engine.475 */476 477static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)478{479 struct ata_port *ap = qc->ap;480 struct pci_dev *pdev = to_pci_dev(ap->host->dev);481 void __iomem *bmdma = ap->ioaddr.bmdma_addr;482 u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);483 u8 dma_cmd;484 485 if (dma_stat & ATA_DMA_ACTIVE) {486 udelay(20);487 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);488 }489 if (dma_stat & ATA_DMA_ACTIVE) {490 /* Clear the engine */491 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);492 udelay(10);493 /* Stop DMA */494 dma_cmd = ioread8(bmdma + ATA_DMA_CMD);495 iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD);496 /* Clear Error */497 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);498 iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR,499 bmdma + ATA_DMA_STATUS);500 /* Clear the engine */501 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);502 udelay(10);503 }504 ata_bmdma_stop(qc);505}506 507/**508 * hpt37x_bmdma_stop - DMA engine stop509 * @qc: ATA command510 *511 * Clean up after the HPT372 and later DMA engine512 */513 514static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc)515{516 struct ata_port *ap = qc->ap;517 struct pci_dev *pdev = to_pci_dev(ap->host->dev);518 int mscreg = 0x50 + 4 * ap->port_no;519 u8 bwsr_stat, msc_stat;520 521 pci_read_config_byte(pdev, 0x6A, &bwsr_stat);522 pci_read_config_byte(pdev, mscreg, &msc_stat);523 if (bwsr_stat & (1 << ap->port_no))524 pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);525 ata_bmdma_stop(qc);526}527 528 529static const struct scsi_host_template hpt37x_sht = {530 ATA_BMDMA_SHT(DRV_NAME),531};532 533/*534 * Configuration for HPT370535 */536 537static struct ata_port_operations hpt370_port_ops = {538 .inherits = &ata_bmdma_port_ops,539 540 .bmdma_stop = hpt370_bmdma_stop,541 542 .mode_filter = hpt370_filter,543 .cable_detect = hpt37x_cable_detect,544 .set_piomode = hpt37x_set_piomode,545 .set_dmamode = hpt37x_set_dmamode,546 .prereset = hpt37x_pre_reset,547};548 549/*550 * Configuration for HPT370A. Close to 370 but less filters551 */552 553static struct ata_port_operations hpt370a_port_ops = {554 .inherits = &hpt370_port_ops,555 .mode_filter = hpt370a_filter,556};557 558/*559 * Configuration for HPT371 and HPT302.560 */561 562static struct ata_port_operations hpt302_port_ops = {563 .inherits = &ata_bmdma_port_ops,564 565 .bmdma_stop = hpt37x_bmdma_stop,566 567 .cable_detect = hpt37x_cable_detect,568 .set_piomode = hpt37x_set_piomode,569 .set_dmamode = hpt37x_set_dmamode,570 .prereset = hpt37x_pre_reset,571};572 573/*574 * Configuration for HPT372. Mode setting works like 371 and 302575 * but we have a mode filter.576 */577 578static struct ata_port_operations hpt372_port_ops = {579 .inherits = &hpt302_port_ops,580 .mode_filter = hpt372_filter,581};582 583/*584 * Configuration for HPT374. Mode setting and filtering works like 372585 * but we have a different cable detection procedure for function 1.586 */587 588static struct ata_port_operations hpt374_fn1_port_ops = {589 .inherits = &hpt372_port_ops,590 .cable_detect = hpt374_fn1_cable_detect,591};592 593/**594 * hpt37x_clock_slot - Turn timing to PC clock entry595 * @freq: Reported frequency in MHz596 *597 * Turn the timing data into a clock slot (0 for 33, 1 for 40, 2 for 50598 * and 3 for 66Mhz)599 */600 601static int hpt37x_clock_slot(unsigned int freq)602{603 if (freq < 40)604 return 0; /* 33Mhz slot */605 if (freq < 45)606 return 1; /* 40Mhz slot */607 if (freq < 55)608 return 2; /* 50Mhz slot */609 return 3; /* 60Mhz slot */610}611 612/**613 * hpt37x_calibrate_dpll - Calibrate the DPLL loop614 * @dev: PCI device615 *616 * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this617 * succeeds618 */619 620static int hpt37x_calibrate_dpll(struct pci_dev *dev)621{622 u8 reg5b;623 u32 reg5c;624 int tries;625 626 for (tries = 0; tries < 0x5000; tries++) {627 udelay(50);628 pci_read_config_byte(dev, 0x5b, ®5b);629 if (reg5b & 0x80) {630 /* See if it stays set */631 for (tries = 0; tries < 0x1000; tries++) {632 pci_read_config_byte(dev, 0x5b, ®5b);633 /* Failed ? */634 if ((reg5b & 0x80) == 0)635 return 0;636 }637 /* Turn off tuning, we have the DPLL set */638 pci_read_config_dword(dev, 0x5c, ®5c);639 pci_write_config_dword(dev, 0x5c, reg5c & ~0x100);640 return 1;641 }642 }643 /* Never went stable */644 return 0;645}646 647static int hpt37x_pci_clock(struct pci_dev *pdev, unsigned int base)648{649 unsigned int freq;650 u32 fcnt;651 652 /*653 * Some devices do not let this value be accessed via PCI space654 * according to the old driver. In addition we must use the value655 * from FN 0 on the HPT374.656 */657 if (pdev->device == PCI_DEVICE_ID_TTI_HPT374 &&658 (PCI_FUNC(pdev->devfn) & 1)) {659 struct pci_dev *pdev_fn0;660 661 pdev_fn0 = pci_get_slot(pdev->bus, pdev->devfn - 1);662 /* Someone hot plugged the controller on us? */663 if (!pdev_fn0)664 return 0;665 fcnt = inl(pci_resource_start(pdev_fn0, 4) + 0x90);666 pci_dev_put(pdev_fn0);667 } else {668 fcnt = inl(pci_resource_start(pdev, 4) + 0x90);669 }670 671 if ((fcnt >> 12) != 0xABCDE) {672 u32 total = 0;673 int i;674 u16 sr;675 676 dev_warn(&pdev->dev, "BIOS clock data not set\n");677 678 /* This is the process the HPT371 BIOS is reported to use */679 for (i = 0; i < 128; i++) {680 pci_read_config_word(pdev, 0x78, &sr);681 total += sr & 0x1FF;682 udelay(15);683 }684 fcnt = total / 128;685 }686 fcnt &= 0x1FF;687 688 freq = (fcnt * base) / 192; /* in MHz */689 690 /* Clamp to bands */691 if (freq < 40)692 return 33;693 if (freq < 45)694 return 40;695 if (freq < 55)696 return 50;697 return 66;698}699 700/**701 * hpt37x_init_one - Initialise an HPT37X/302702 * @dev: PCI device703 * @id: Entry in match table704 *705 * Initialise an HPT37x device. There are some interesting complications706 * here. Firstly the chip may report 366 and be one of several variants.707 * Secondly all the timings depend on the clock for the chip which we must708 * detect and look up709 *710 * This is the known chip mappings. It may be missing a couple of later711 * releases.712 *713 * Chip version PCI Rev Notes714 * HPT366 4 (HPT366) 0 Other driver715 * HPT366 4 (HPT366) 1 Other driver716 * HPT368 4 (HPT366) 2 Other driver717 * HPT370 4 (HPT366) 3 UDMA100718 * HPT370A 4 (HPT366) 4 UDMA100719 * HPT372 4 (HPT366) 5 UDMA133 (1)720 * HPT372N 4 (HPT366) 6 Other driver721 * HPT372A 5 (HPT372) 1 UDMA133 (1)722 * HPT372N 5 (HPT372) 2 Other driver723 * HPT302 6 (HPT302) 1 UDMA133724 * HPT302N 6 (HPT302) 2 Other driver725 * HPT371 7 (HPT371) * UDMA133726 * HPT374 8 (HPT374) * UDMA133 4 channel727 * HPT372N 9 (HPT372N) * Other driver728 *729 * (1) UDMA133 support depends on the bus clock730 */731 732static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)733{734 /* HPT370 - UDMA100 */735 static const struct ata_port_info info_hpt370 = {736 .flags = ATA_FLAG_SLAVE_POSS,737 .pio_mask = ATA_PIO4,738 .mwdma_mask = ATA_MWDMA2,739 .udma_mask = ATA_UDMA5,740 .port_ops = &hpt370_port_ops741 };742 /* HPT370A - UDMA100 */743 static const struct ata_port_info info_hpt370a = {744 .flags = ATA_FLAG_SLAVE_POSS,745 .pio_mask = ATA_PIO4,746 .mwdma_mask = ATA_MWDMA2,747 .udma_mask = ATA_UDMA5,748 .port_ops = &hpt370a_port_ops749 };750 /* HPT370 - UDMA66 */751 static const struct ata_port_info info_hpt370_33 = {752 .flags = ATA_FLAG_SLAVE_POSS,753 .pio_mask = ATA_PIO4,754 .mwdma_mask = ATA_MWDMA2,755 .udma_mask = ATA_UDMA4,756 .port_ops = &hpt370_port_ops757 };758 /* HPT370A - UDMA66 */759 static const struct ata_port_info info_hpt370a_33 = {760 .flags = ATA_FLAG_SLAVE_POSS,761 .pio_mask = ATA_PIO4,762 .mwdma_mask = ATA_MWDMA2,763 .udma_mask = ATA_UDMA4,764 .port_ops = &hpt370a_port_ops765 };766 /* HPT372 - UDMA133 */767 static const struct ata_port_info info_hpt372 = {768 .flags = ATA_FLAG_SLAVE_POSS,769 .pio_mask = ATA_PIO4,770 .mwdma_mask = ATA_MWDMA2,771 .udma_mask = ATA_UDMA6,772 .port_ops = &hpt372_port_ops773 };774 /* HPT371, 302 - UDMA133 */775 static const struct ata_port_info info_hpt302 = {776 .flags = ATA_FLAG_SLAVE_POSS,777 .pio_mask = ATA_PIO4,778 .mwdma_mask = ATA_MWDMA2,779 .udma_mask = ATA_UDMA6,780 .port_ops = &hpt302_port_ops781 };782 /* HPT374 - UDMA100, function 1 uses different cable_detect method */783 static const struct ata_port_info info_hpt374_fn0 = {784 .flags = ATA_FLAG_SLAVE_POSS,785 .pio_mask = ATA_PIO4,786 .mwdma_mask = ATA_MWDMA2,787 .udma_mask = ATA_UDMA5,788 .port_ops = &hpt372_port_ops789 };790 static const struct ata_port_info info_hpt374_fn1 = {791 .flags = ATA_FLAG_SLAVE_POSS,792 .pio_mask = ATA_PIO4,793 .mwdma_mask = ATA_MWDMA2,794 .udma_mask = ATA_UDMA5,795 .port_ops = &hpt374_fn1_port_ops796 };797 798 static const int MHz[4] = { 33, 40, 50, 66 };799 void *private_data = NULL;800 const struct ata_port_info *ppi[] = { NULL, NULL };801 u8 rev = dev->revision;802 u8 irqmask;803 u8 mcr1;804 unsigned int freq; /* MHz */805 int prefer_dpll = 1;806 807 unsigned long iobase = pci_resource_start(dev, 4);808 809 const struct hpt_chip *chip_table;810 int clock_slot;811 int rc;812 813 rc = pcim_enable_device(dev);814 if (rc)815 return rc;816 817 switch (dev->device) {818 case PCI_DEVICE_ID_TTI_HPT366:819 /* May be a later chip in disguise. Check */820 /* Older chips are in the HPT366 driver. Ignore them */821 if (rev < 3)822 return -ENODEV;823 /* N series chips have their own driver. Ignore */824 if (rev == 6)825 return -ENODEV;826 827 switch (rev) {828 case 3:829 ppi[0] = &info_hpt370;830 chip_table = &hpt370;831 prefer_dpll = 0;832 break;833 case 4:834 ppi[0] = &info_hpt370a;835 chip_table = &hpt370a;836 prefer_dpll = 0;837 break;838 case 5:839 ppi[0] = &info_hpt372;840 chip_table = &hpt372;841 break;842 default:843 dev_err(&dev->dev,844 "Unknown HPT366 subtype, please report (%d)\n",845 rev);846 return -ENODEV;847 }848 break;849 case PCI_DEVICE_ID_TTI_HPT372:850 /* 372N if rev >= 2 */851 if (rev >= 2)852 return -ENODEV;853 ppi[0] = &info_hpt372;854 chip_table = &hpt372a;855 break;856 case PCI_DEVICE_ID_TTI_HPT302:857 /* 302N if rev > 1 */858 if (rev > 1)859 return -ENODEV;860 ppi[0] = &info_hpt302;861 /* Check this */862 chip_table = &hpt302;863 break;864 case PCI_DEVICE_ID_TTI_HPT371:865 if (rev > 1)866 return -ENODEV;867 ppi[0] = &info_hpt302;868 chip_table = &hpt371;869 /*870 * Single channel device, master is not present but the BIOS871 * (or us for non x86) must mark it absent872 */873 pci_read_config_byte(dev, 0x50, &mcr1);874 mcr1 &= ~0x04;875 pci_write_config_byte(dev, 0x50, mcr1);876 break;877 case PCI_DEVICE_ID_TTI_HPT374:878 chip_table = &hpt374;879 if (!(PCI_FUNC(dev->devfn) & 1))880 *ppi = &info_hpt374_fn0;881 else882 *ppi = &info_hpt374_fn1;883 break;884 default:885 dev_err(&dev->dev, "PCI table is bogus, please report (%d)\n",886 dev->device);887 return -ENODEV;888 }889 /* Ok so this is a chip we support */890 891 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));892 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);893 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);894 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);895 896 pci_read_config_byte(dev, 0x5A, &irqmask);897 irqmask &= ~0x10;898 pci_write_config_byte(dev, 0x5a, irqmask);899 900 /*901 * HPT371 chips physically have only one channel, the secondary one,902 * but the primary channel registers do exist! Go figure...903 * So, we manually disable the non-existing channel here904 * (if the BIOS hasn't done this already).905 */906 if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {907 u8 mcr1;908 909 pci_read_config_byte(dev, 0x50, &mcr1);910 mcr1 &= ~0x04;911 pci_write_config_byte(dev, 0x50, mcr1);912 }913 914 /*915 * default to pci clock. make sure MA15/16 are set to output916 * to prevent drives having problems with 40-pin cables. Needed917 * for some drives such as IBM-DTLA which will not enter ready918 * state on reset when PDIAG is a input.919 */920 921 pci_write_config_byte(dev, 0x5b, 0x23);922 923 /*924 * HighPoint does this for HPT372A.925 * NOTE: This register is only writeable via I/O space.926 */927 if (chip_table == &hpt372a)928 outb(0x0e, iobase + 0x9c);929 930 freq = hpt37x_pci_clock(dev, chip_table->base);931 if (!freq)932 return -ENODEV;933 934 /*935 * Turn the frequency check into a band and then find a timing936 * table to match it.937 */938 939 clock_slot = hpt37x_clock_slot(freq);940 if (chip_table->clocks[clock_slot] == NULL || prefer_dpll) {941 /*942 * We need to try PLL mode instead943 *944 * For non UDMA133 capable devices we should945 * use a 50MHz DPLL by choice946 */947 unsigned int f_low, f_high;948 int dpll, adjust;949 950 /* Compute DPLL */951 dpll = (ppi[0]->udma_mask & 0xC0) ? 3 : 2;952 953 f_low = (MHz[clock_slot] * 48) / MHz[dpll];954 f_high = f_low + 2;955 if (clock_slot > 1)956 f_high += 2;957 958 /* Select the DPLL clock. */959 pci_write_config_byte(dev, 0x5b, 0x21);960 pci_write_config_dword(dev, 0x5C,961 (f_high << 16) | f_low | 0x100);962 963 for (adjust = 0; adjust < 8; adjust++) {964 if (hpt37x_calibrate_dpll(dev))965 break;966 /*967 * See if it'll settle at a fractionally968 * different clock969 */970 if (adjust & 1)971 f_low -= adjust >> 1;972 else973 f_high += adjust >> 1;974 pci_write_config_dword(dev, 0x5C,975 (f_high << 16) | f_low | 0x100);976 }977 if (adjust == 8) {978 dev_err(&dev->dev, "DPLL did not stabilize!\n");979 return -ENODEV;980 }981 if (dpll == 3)982 private_data = (void *)hpt37x_timings_66;983 else984 private_data = (void *)hpt37x_timings_50;985 986 dev_info(&dev->dev, "bus clock %dMHz, using %dMHz DPLL\n",987 MHz[clock_slot], MHz[dpll]);988 } else {989 private_data = (void *)chip_table->clocks[clock_slot];990 /*991 * Perform a final fixup. Note that we will have used the992 * DPLL on the HPT372 which means we don't have to worry993 * about lack of UDMA133 support on lower clocks994 */995 996 if (clock_slot < 2 && ppi[0] == &info_hpt370)997 ppi[0] = &info_hpt370_33;998 if (clock_slot < 2 && ppi[0] == &info_hpt370a)999 ppi[0] = &info_hpt370a_33;1000 1001 dev_info(&dev->dev, "%s using %dMHz bus clock\n",1002 chip_table->name, MHz[clock_slot]);1003 }1004 1005 /* Now kick off ATA set up */1006 return ata_pci_bmdma_init_one(dev, ppi, &hpt37x_sht, private_data, 0);1007}1008 1009static const struct pci_device_id hpt37x[] = {1010 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },1011 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },1012 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },1013 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), },1014 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },1015 1016 { },1017};1018 1019static struct pci_driver hpt37x_pci_driver = {1020 .name = DRV_NAME,1021 .id_table = hpt37x,1022 .probe = hpt37x_init_one,1023 .remove = ata_pci_remove_one1024};1025 1026module_pci_driver(hpt37x_pci_driver);1027 1028MODULE_AUTHOR("Alan Cox");1029MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");1030MODULE_LICENSE("GPL");1031MODULE_DEVICE_TABLE(pci, hpt37x);1032MODULE_VERSION(DRV_VERSION);1033