brintos

brintos / linux-shallow public Read only

0
0
Text · 26.9 KiB · e48b861 Raw
986 lines · c
1/* SPDX-License-Identifier: GPL-2.0-only */2/*3 * Copyright (C) 2005 - 2016 Broadcom4 * All rights reserved.5 *6 * Contact Information:7 * linux-drivers@emulex.com8 *9 * Emulex10 * 3333 Susan Street11 * Costa Mesa, CA 9262612 */13 14#ifndef BE_H15#define BE_H16 17#include <linux/pci.h>18#include <linux/etherdevice.h>19#include <linux/delay.h>20#include <net/tcp.h>21#include <net/ip.h>22#include <net/ipv6.h>23#include <linux/if_vlan.h>24#include <linux/workqueue.h>25#include <linux/interrupt.h>26#include <linux/firmware.h>27#include <linux/slab.h>28#include <linux/u64_stats_sync.h>29#include <linux/cpumask.h>30#include <linux/hwmon.h>31#include <linux/hwmon-sysfs.h>32 33#include "be_hw.h"34#include "be_roce.h"35 36#define DRV_NAME		"be2net"37#define BE_NAME			"Emulex BladeEngine2"38#define BE3_NAME		"Emulex BladeEngine3"39#define OC_NAME			"Emulex OneConnect"40#define OC_NAME_BE		OC_NAME	"(be3)"41#define OC_NAME_LANCER		OC_NAME "(Lancer)"42#define OC_NAME_SH		OC_NAME "(Skyhawk)"43#define DRV_DESC		"Emulex OneConnect NIC Driver"44 45#define BE_VENDOR_ID 		0x19a246#define EMULEX_VENDOR_ID	0x10df47#define BE_DEVICE_ID1		0x21148#define BE_DEVICE_ID2		0x22149#define OC_DEVICE_ID1		0x700	/* Device Id for BE2 cards */50#define OC_DEVICE_ID2		0x710	/* Device Id for BE3 cards */51#define OC_DEVICE_ID3		0xe220	/* Device id for Lancer cards */52#define OC_DEVICE_ID4           0xe228   /* Device id for VF in Lancer */53#define OC_DEVICE_ID5		0x720	/* Device Id for Skyhawk cards */54#define OC_DEVICE_ID6		0x728   /* Device id for VF in SkyHawk */55#define OC_SUBSYS_DEVICE_ID1	0xE60256#define OC_SUBSYS_DEVICE_ID2	0xE64257#define OC_SUBSYS_DEVICE_ID3	0xE61258#define OC_SUBSYS_DEVICE_ID4	0xE65259 60/* Number of bytes of an RX frame that are copied to skb->data */61#define BE_HDR_LEN		((u16) 64)62/* allocate extra space to allow tunneling decapsulation without head reallocation */63#define BE_RX_SKB_ALLOC_SIZE	25664 65#define BE_MAX_JUMBO_FRAME_SIZE	901866#define BE_MIN_MTU		25667#define BE_MAX_MTU              (BE_MAX_JUMBO_FRAME_SIZE -	\68				 (ETH_HLEN + ETH_FCS_LEN))69 70/* Accommodate for QnQ configurations where VLAN insertion is enabled in HW */71#define BE_MAX_GSO_SIZE		(65535 - 2 * VLAN_HLEN)72 73#define BE_NUM_VLANS_SUPPORTED	6474#define BE_MAX_EQD		128u75#define	BE_MAX_TX_FRAG_COUNT	3076 77#define EVNT_Q_LEN		102478#define TX_Q_LEN		204879#define TX_CQ_LEN		102480#define RX_Q_LEN		1024	/* Does not support any other value */81#define RX_CQ_LEN		102482#define MCC_Q_LEN		128	/* total size not to exceed 8 pages */83#define MCC_CQ_LEN		25684 85#define BE2_MAX_RSS_QS		486#define BE3_MAX_RSS_QS		1687#define BE3_MAX_TX_QS		1688#define BE3_MAX_EVT_QS		1689#define BE3_SRIOV_MAX_EVT_QS	890#define SH_VF_MAX_NIC_EQS	3	/* Skyhawk VFs can have a max of 4 EQs91					 * and at least 1 is granted to either92					 * SURF/DPDK93					 */94 95#define MAX_PORT_RSS_TABLES	1596#define MAX_NIC_FUNCS		1697#define MAX_RX_QS		3298#define MAX_EVT_QS		3299#define MAX_TX_QS		32100 101#define MAX_ROCE_EQS		5102#define MAX_MSIX_VECTORS	32103#define MIN_MSIX_VECTORS	1104#define MAX_RX_POST		NAPI_POLL_WEIGHT /* Frags posted at a time */105#define RX_FRAGS_REFILL_WM	(RX_Q_LEN - MAX_RX_POST)106#define MAX_NUM_POST_ERX_DB	255u107 108#define MAX_VFS			30 /* Max VFs supported by BE3 FW */109#define FW_VER_LEN		32110#define	CNTL_SERIAL_NUM_WORDS	8  /* Controller serial number words */111#define	CNTL_SERIAL_NUM_WORD_SZ	(sizeof(u16)) /* Byte-sz of serial num word */112 113#define	RSS_INDIR_TABLE_LEN	128114#define RSS_HASH_KEY_LEN	40115 116#define BE_UNKNOWN_PHY_STATE	0xFF117 118struct be_dma_mem {119	void *va;120	dma_addr_t dma;121	u32 size;122};123 124struct be_queue_info {125	u32 len;126	u32 entry_size;	/* Size of an element in the queue */127	u32 tail, head;128	atomic_t used;	/* Number of valid elements in the queue */129	u32 id;130	struct be_dma_mem dma_mem;131	bool created;132};133 134static inline u32 MODULO(u32 val, u32 limit)135{136	BUG_ON(limit & (limit - 1));137	return val & (limit - 1);138}139 140static inline void index_adv(u32 *index, u32 val, u32 limit)141{142	*index = MODULO((*index + val), limit);143}144 145static inline void index_inc(u32 *index, u32 limit)146{147	*index = MODULO((*index + 1), limit);148}149 150static inline void *queue_head_node(struct be_queue_info *q)151{152	return q->dma_mem.va + q->head * q->entry_size;153}154 155static inline void *queue_tail_node(struct be_queue_info *q)156{157	return q->dma_mem.va + q->tail * q->entry_size;158}159 160static inline void *queue_index_node(struct be_queue_info *q, u16 index)161{162	return q->dma_mem.va + index * q->entry_size;163}164 165static inline void queue_head_inc(struct be_queue_info *q)166{167	index_inc(&q->head, q->len);168}169 170static inline void index_dec(u32 *index, u32 limit)171{172	*index = MODULO((*index - 1), limit);173}174 175static inline void queue_tail_inc(struct be_queue_info *q)176{177	index_inc(&q->tail, q->len);178}179 180struct be_eq_obj {181	struct be_queue_info q;182	char desc[32];183 184	struct be_adapter *adapter;185	struct napi_struct napi;186	u8 idx;			/* array index */187	u8 msix_idx;188	u16 spurious_intr;189	cpumask_var_t  affinity_mask;190} ____cacheline_aligned_in_smp;191 192struct be_aic_obj {		/* Adaptive interrupt coalescing (AIC) info */193	u32 min_eqd;		/* in usecs */194	u32 max_eqd;		/* in usecs */195	u32 prev_eqd;		/* in usecs */196	u32 et_eqd;		/* configured val when aic is off */197	ulong jiffies;198	u64 rx_pkts_prev;	/* Used to calculate RX pps */199	u64 tx_reqs_prev;	/* Used to calculate TX pps */200};201 202struct be_mcc_obj {203	struct be_queue_info q;204	struct be_queue_info cq;205	bool rearm_cq;206};207 208struct be_tx_stats {209	u64 tx_bytes;210	u64 tx_pkts;211	u64 tx_vxlan_offload_pkts;212	u64 tx_reqs;213	u64 tx_compl;214	u32 tx_stops;215	u32 tx_drv_drops;	/* pkts dropped by driver */216	/* the error counters are described in be_ethtool.c */217	u32 tx_hdr_parse_err;218	u32 tx_dma_err;219	u32 tx_tso_err;220	u32 tx_spoof_check_err;221	u32 tx_qinq_err;222	u32 tx_internal_parity_err;223	u32 tx_sge_err;224	struct u64_stats_sync sync;225	struct u64_stats_sync sync_compl;226};227 228/* Structure to hold some data of interest obtained from a TX CQE */229struct be_tx_compl_info {230	u8 status;		/* Completion status */231	u16 end_index;		/* Completed TXQ Index */232};233 234struct be_tx_obj {235	u32 db_offset;236	struct be_tx_compl_info txcp;237	struct be_queue_info q;238	struct be_queue_info cq;239	/* Remember the skbs that were transmitted */240	struct sk_buff *sent_skb_list[TX_Q_LEN];241	struct be_tx_stats stats;242	u16 pend_wrb_cnt;	/* Number of WRBs yet to be given to HW */243	u16 last_req_wrb_cnt;	/* wrb cnt of the last req in the Q */244	u16 last_req_hdr;	/* index of the last req's hdr-wrb */245} ____cacheline_aligned_in_smp;246 247/* Struct to remember the pages posted for rx frags */248struct be_rx_page_info {249	struct page *page;250	/* set to page-addr for last frag of the page & frag-addr otherwise */251	DEFINE_DMA_UNMAP_ADDR(bus);252	u16 page_offset;253	bool last_frag;		/* last frag of the page */254};255 256struct be_rx_stats {257	u64 rx_bytes;258	u64 rx_pkts;259	u64 rx_vxlan_offload_pkts;260	u32 rx_drops_no_skbs;	/* skb allocation errors */261	u32 rx_drops_no_frags;	/* HW has no fetched frags */262	u32 rx_post_fail;	/* page post alloc failures */263	u32 rx_compl;264	u32 rx_mcast_pkts;265	u32 rx_compl_err;	/* completions with err set */266	struct u64_stats_sync sync;267};268 269struct be_rx_compl_info {270	u32 rss_hash;271	u16 vlan_tag;272	u16 pkt_size;273	u16 port;274	u8 vlanf;275	u8 num_rcvd;276	u8 err;277	u8 ipf;278	u8 tcpf;279	u8 udpf;280	u8 ip_csum;281	u8 l4_csum;282	u8 ipv6;283	u8 qnq;284	u8 pkt_type;285	u8 ip_frag;286	u8 tunneled;287};288 289struct be_rx_obj {290	struct be_adapter *adapter;291	struct be_queue_info q;292	struct be_queue_info cq;293	struct be_rx_compl_info rxcp;294	struct be_rx_page_info page_info_tbl[RX_Q_LEN];295	struct be_rx_stats stats;296	u8 rss_id;297	bool rx_post_starved;	/* Zero rx frags have been posted to BE */298} ____cacheline_aligned_in_smp;299 300struct be_drv_stats {301	u32 eth_red_drops;302	u32 dma_map_errors;303	u32 rx_drops_no_pbuf;304	u32 rx_drops_no_txpb;305	u32 rx_drops_no_erx_descr;306	u32 rx_drops_no_tpre_descr;307	u32 rx_drops_too_many_frags;308	u32 forwarded_packets;309	u32 rx_drops_mtu;310	u32 rx_crc_errors;311	u32 rx_alignment_symbol_errors;312	u32 rx_pause_frames;313	u32 rx_priority_pause_frames;314	u32 rx_control_frames;315	u32 rx_in_range_errors;316	u32 rx_out_range_errors;317	u32 rx_frame_too_long;318	u32 rx_address_filtered;319	u32 rx_dropped_too_small;320	u32 rx_dropped_too_short;321	u32 rx_dropped_header_too_small;322	u32 rx_dropped_tcp_length;323	u32 rx_dropped_runt;324	u32 rx_ip_checksum_errs;325	u32 rx_tcp_checksum_errs;326	u32 rx_udp_checksum_errs;327	u32 tx_pauseframes;328	u32 tx_priority_pauseframes;329	u32 tx_controlframes;330	u32 rxpp_fifo_overflow_drop;331	u32 rx_input_fifo_overflow_drop;332	u32 pmem_fifo_overflow_drop;333	u32 jabber_events;334	u32 rx_roce_bytes_lsd;335	u32 rx_roce_bytes_msd;336	u32 rx_roce_frames;337	u32 roce_drops_payload_len;338	u32 roce_drops_crc;339};340 341/* A vlan-id of 0xFFFF must be used to clear transparent vlan-tagging */342#define BE_RESET_VLAN_TAG_ID	0xFFFF343 344struct be_vf_cfg {345	unsigned char mac_addr[ETH_ALEN];346	int if_handle;347	int pmac_id;348	u16 vlan_tag;349	u32 tx_rate;350	u32 plink_tracking;351	u32 privileges;352	bool spoofchk;353};354 355enum vf_state {356	ENABLED = 0,357	ASSIGNED = 1358};359 360#define BE_FLAGS_LINK_STATUS_INIT		BIT(1)361#define BE_FLAGS_SRIOV_ENABLED			BIT(2)362#define BE_FLAGS_WORKER_SCHEDULED		BIT(3)363#define BE_FLAGS_NAPI_ENABLED			BIT(6)364#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD		BIT(7)365#define BE_FLAGS_VXLAN_OFFLOADS			BIT(8)366#define BE_FLAGS_SETUP_DONE			BIT(9)367#define BE_FLAGS_PHY_MISCONFIGURED		BIT(10)368#define BE_FLAGS_ERR_DETECTION_SCHEDULED	BIT(11)369#define BE_FLAGS_OS2BMC				BIT(12)370#define BE_FLAGS_TRY_RECOVERY			BIT(13)371 372#define BE_UC_PMAC_COUNT			30373#define BE_VF_UC_PMAC_COUNT			2374 375#define MAX_ERR_RECOVERY_RETRY_COUNT		3376#define ERR_DETECTION_DELAY			1000377 378/* Ethtool set_dump flags */379#define LANCER_INITIATE_FW_DUMP			0x1380#define LANCER_DELETE_FW_DUMP			0x2381 382struct phy_info {383/* From SFF-8472 spec */384#define SFP_VENDOR_NAME_LEN			17385	u8 transceiver;386	u8 autoneg;387	u8 fc_autoneg;388	u8 port_type;389	u16 phy_type;390	u16 interface_type;391	u32 misc_params;392	u16 auto_speeds_supported;393	u16 fixed_speeds_supported;394	int link_speed;395	u32 advertising;396	u32 supported;397	u8 cable_type;398	u8 vendor_name[SFP_VENDOR_NAME_LEN];399	u8 vendor_pn[SFP_VENDOR_NAME_LEN];400};401 402struct be_resources {403	u16 max_vfs;		/* Total VFs "really" supported by FW/HW */404	u16 max_mcast_mac;405	u16 max_tx_qs;406	u16 max_rss_qs;407	u16 max_rx_qs;408	u16 max_cq_count;409	u16 max_uc_mac;		/* Max UC MACs programmable */410	u16 max_vlans;		/* Number of vlans supported */411	u16 max_iface_count;412	u16 max_mcc_count;413	u16 max_evt_qs;414	u16 max_nic_evt_qs;	/* NIC's share of evt qs */415	u32 if_cap_flags;416	u32 vf_if_cap_flags;	/* VF if capability flags */417	u32 flags;418	/* Calculated PF Pool's share of RSS Tables. This is not enforced by419	 * the FW, but is a self-imposed driver limitation.420	 */421	u16 max_rss_tables;422};423 424/* These are port-wide values */425struct be_port_resources {426	u16 max_vfs;427	u16 nic_pfs;428};429 430#define be_is_os2bmc_enabled(adapter) (adapter->flags & BE_FLAGS_OS2BMC)431 432struct rss_info {433	u8 rsstable[RSS_INDIR_TABLE_LEN];434	u8 rss_queue[RSS_INDIR_TABLE_LEN];435	u8 rss_hkey[RSS_HASH_KEY_LEN];436	u64 rss_flags;437};438 439#define BE_INVALID_DIE_TEMP	0xFF440struct be_hwmon {441	struct device *hwmon_dev;442	u8 be_on_die_temp;  /* Unit: millidegree Celsius */443};444 445/* Macros to read/write the 'features' word of be_wrb_params structure.446 */447#define	BE_WRB_F_BIT(name)			BE_WRB_F_##name##_BIT448#define	BE_WRB_F_MASK(name)			BIT_MASK(BE_WRB_F_##name##_BIT)449 450#define	BE_WRB_F_GET(word, name)	\451	(((word) & (BE_WRB_F_MASK(name))) >> BE_WRB_F_BIT(name))452 453#define	BE_WRB_F_SET(word, name, val)	\454	((word) |= (((val) << BE_WRB_F_BIT(name)) & BE_WRB_F_MASK(name)))455 456/* Feature/offload bits */457enum {458	BE_WRB_F_CRC_BIT,		/* Ethernet CRC */459	BE_WRB_F_IPCS_BIT,		/* IP csum */460	BE_WRB_F_TCPCS_BIT,		/* TCP csum */461	BE_WRB_F_UDPCS_BIT,		/* UDP csum */462	BE_WRB_F_LSO_BIT,		/* LSO */463	BE_WRB_F_LSO6_BIT,		/* LSO6 */464	BE_WRB_F_VLAN_BIT,		/* VLAN */465	BE_WRB_F_VLAN_SKIP_HW_BIT,	/* Skip VLAN tag (workaround) */466	BE_WRB_F_OS2BMC_BIT		/* Send packet to the management ring */467};468 469/* The structure below provides a HW-agnostic abstraction of WRB params470 * retrieved from a TX skb. This is in turn passed to chip specific routines471 * during transmit, to set the corresponding params in the WRB.472 */473struct be_wrb_params {474	u32 features;	/* Feature bits */475	u16 vlan_tag;	/* VLAN tag */476	u16 lso_mss;	/* MSS for LSO */477};478 479struct be_eth_addr {480	unsigned char mac[ETH_ALEN];481};482 483#define BE_SEC	1000			/* in msec */484#define BE_MIN	(60 * BE_SEC)		/* in msec */485#define BE_HOUR	(60 * BE_MIN)		/* in msec */486 487#define ERR_RECOVERY_MAX_RETRY_COUNT		3488#define ERR_RECOVERY_DETECTION_DELAY		BE_SEC489#define ERR_RECOVERY_RETRY_DELAY		(30 * BE_SEC)490 491/* UE-detection-duration in BEx/Skyhawk:492 * All PFs must wait for this duration after they detect UE before reading493 * SLIPORT_SEMAPHORE register. At the end of this duration, the Firmware494 * guarantees that the SLIPORT_SEMAPHORE register is updated to indicate495 * if the UE is recoverable.496 */497#define ERR_RECOVERY_UE_DETECT_DURATION			BE_SEC498 499/* Initial idle time (in msec) to elapse after driver load,500 * before UE recovery is allowed.501 */502#define ERR_IDLE_HR			24503#define ERR_RECOVERY_IDLE_TIME		(ERR_IDLE_HR * BE_HOUR)504 505/* Time interval (in msec) after which UE recovery can be repeated */506#define ERR_INTERVAL_HR			72507#define ERR_RECOVERY_INTERVAL		(ERR_INTERVAL_HR * BE_HOUR)508 509/* BEx/SH UE recovery state machine */510enum {511	ERR_RECOVERY_ST_NONE = 0,		/* No Recovery */512	ERR_RECOVERY_ST_DETECT = 1,		/* UE detection duration */513	ERR_RECOVERY_ST_RESET = 2,		/* Reset Phase (PF0 only) */514	ERR_RECOVERY_ST_PRE_POLL = 3,		/* Pre-Poll Phase (all PFs) */515	ERR_RECOVERY_ST_REINIT = 4		/* Re-initialize Phase */516};517 518struct be_error_recovery {519	union {520		u8 recovery_retries;	/* used for Lancer		*/521		u8 recovery_state;	/* used for BEx and Skyhawk	*/522	};523 524	/* BEx/Skyhawk error recovery variables */525	bool recovery_supported;526	u16 ue_to_reset_time;		/* Time after UE, to soft reset527					 * the chip - PF0 only528					 */529	u16 ue_to_poll_time;		/* Time after UE, to Restart Polling530					 * of SLIPORT_SEMAPHORE reg531					 */532	u16 last_err_code;533	unsigned long probe_time;534	unsigned long last_recovery_time;535 536	/* Common to both Lancer & BEx/SH error recovery */537	u32 resched_delay;538	struct delayed_work err_detection_work;539};540 541/* Ethtool priv_flags */542#define	BE_DISABLE_TPE_RECOVERY	0x1543 544struct be_vxlan_port {545	struct list_head list;546	__be16 port;		/* VxLAN UDP dst port */547	int port_aliases;	/* alias count */548};549 550struct be_adapter {551	struct pci_dev *pdev;552	struct net_device *netdev;553 554	u8 __iomem *csr;	/* CSR BAR used only for BE2/3 */555	u8 __iomem *db;		/* Door Bell */556	u8 __iomem *pcicfg;	/* On SH,BEx only. Shadow of PCI config space */557 558	struct mutex mbox_lock; /* For serializing mbox cmds to BE card */559	struct be_dma_mem mbox_mem;560	/* Mbox mem is adjusted to align to 16 bytes. The allocated addr561	 * is stored for freeing purpose */562	struct be_dma_mem mbox_mem_alloced;563 564	struct be_mcc_obj mcc_obj;565	struct mutex mcc_lock;	/* For serializing mcc cmds to BE card */566	spinlock_t mcc_cq_lock;567 568	u16 cfg_num_rx_irqs;		/* configured via set-channels */569	u16 cfg_num_tx_irqs;		/* configured via set-channels */570	u16 num_evt_qs;571	u16 num_msix_vec;572	struct be_eq_obj eq_obj[MAX_EVT_QS];573	struct msix_entry msix_entries[MAX_MSIX_VECTORS];574	bool isr_registered;575 576	/* TX Rings */577	u16 num_tx_qs;578	struct be_tx_obj tx_obj[MAX_TX_QS];579 580	/* Rx rings */581	u16 num_rx_qs;582	u16 num_rss_qs;583	u16 need_def_rxq;584	struct be_rx_obj rx_obj[MAX_RX_QS];585	u32 big_page_size;	/* Compounded page size shared by rx wrbs */586 587	struct be_drv_stats drv_stats;588	struct be_aic_obj aic_obj[MAX_EVT_QS];589	bool aic_enabled;590	u8 vlan_prio_bmap;	/* Available Priority BitMap */591	u16 recommended_prio_bits;/* Recommended Priority bits in vlan tag */592	struct be_dma_mem rx_filter; /* Cmd DMA mem for rx-filter */593 594	struct be_dma_mem stats_cmd;595	/* Work queue used to perform periodic tasks like getting statistics */596	struct delayed_work work;597	u16 work_counter;598 599	u8 recovery_retries;600	u8 err_flags;601	bool pcicfg_mapped;	/* pcicfg obtained via pci_iomap() */602	u32 flags;603	u32 cmd_privileges;604	/* Ethtool knobs and info */605	char fw_ver[FW_VER_LEN];606	char fw_on_flash[FW_VER_LEN];607 608	/* IFACE filtering fields */609	int if_handle;		/* Used to configure filtering */610	u32 if_flags;		/* Interface filtering flags */611	u32 *pmac_id;		/* MAC addr handle used by BE card */612	struct be_eth_addr *uc_list;/* list of uc-addrs programmed (not perm) */613	u32 uc_macs;		/* Count of secondary UC MAC programmed */614	struct be_eth_addr *mc_list;/* list of mcast addrs programmed */615	u32 mc_count;616	unsigned long vids[BITS_TO_LONGS(VLAN_N_VID)];617	u16 vlans_added;618	bool update_uc_list;619	bool update_mc_list;620	struct mutex rx_filter_lock;/* For protecting vids[] & mc/uc_list[] */621 622	u32 beacon_state;	/* for set_phys_id */623 624	u32 port_num;625	char port_name;626	u8 mc_type;627	u32 function_mode;628	u32 function_caps;629	u32 rx_fc;		/* Rx flow control */630	u32 tx_fc;		/* Tx flow control */631	bool stats_cmd_sent;632	struct {633		u32 size;634		u32 total_size;635		u64 io_addr;636	} roce_db;637	u32 num_msix_roce_vec;638	struct ocrdma_dev *ocrdma_dev;639	struct list_head entry;640 641	u32 flash_status;642	struct completion et_cmd_compl;643 644	struct be_resources pool_res;	/* resources available for the port */645	struct be_resources res;	/* resources available for the func */646	u16 num_vfs;			/* Number of VFs provisioned by PF */647	u8 pf_num;			/* Numbering used by FW, starts at 0 */648	u8 vf_num;			/* Numbering used by FW, starts at 1 */649	u8 virtfn;650	struct be_vf_cfg *vf_cfg;651	bool be3_native;652	u32 sli_family;653	u8 hba_port_num;654	u16 pvid;655	__be16 vxlan_port;		/* offloaded vxlan port num */656	struct phy_info phy;657	u8 wol_cap;658	bool wol_en;659	u16 asic_rev;660	u16 qnq_vid;661	u32 msg_enable;662	int be_get_temp_freq;663	struct be_hwmon hwmon_info;664	struct rss_info rss_info;665	/* Filters for packets that need to be sent to BMC */666	u32 bmc_filt_mask;667	u32 fat_dump_len;668	u16 serial_num[CNTL_SERIAL_NUM_WORDS];669	u8 phy_state; /* state of sfp optics (functional, faulted, etc.,) */670	u8 dev_mac[ETH_ALEN];671	u32 priv_flags; /* ethtool get/set_priv_flags() */672	struct be_error_recovery error_recovery;673};674 675/* Used for defered FW config cmds. Add fields to this struct as reqd */676struct be_cmd_work {677	struct work_struct work;678	struct be_adapter *adapter;679};680 681#define be_physfn(adapter)		(!adapter->virtfn)682#define be_virtfn(adapter)		(adapter->virtfn)683#define sriov_enabled(adapter)		(adapter->flags &	\684					 BE_FLAGS_SRIOV_ENABLED)685 686#define for_all_vfs(adapter, vf_cfg, i)					\687	for (i = 0, vf_cfg = &adapter->vf_cfg[i]; i < adapter->num_vfs;	\688		i++, vf_cfg++)689 690#define ON				1691#define OFF				0692 693#define be_max_vlans(adapter)		(adapter->res.max_vlans)694#define be_max_uc(adapter)		(adapter->res.max_uc_mac)695#define be_max_mc(adapter)		(adapter->res.max_mcast_mac)696#define be_max_vfs(adapter)		(adapter->pool_res.max_vfs)697#define be_max_rss(adapter)		(adapter->res.max_rss_qs)698#define be_max_txqs(adapter)		(adapter->res.max_tx_qs)699#define be_max_prio_txqs(adapter)	(adapter->res.max_prio_tx_qs)700#define be_max_rxqs(adapter)		(adapter->res.max_rx_qs)701/* Max number of EQs available for the function (NIC + RoCE (if enabled)) */702#define be_max_func_eqs(adapter)	(adapter->res.max_evt_qs)703/* Max number of EQs available avaialble only for NIC */704#define be_max_nic_eqs(adapter)		(adapter->res.max_nic_evt_qs)705#define be_if_cap_flags(adapter)	(adapter->res.if_cap_flags)706#define be_max_pf_pool_rss_tables(adapter)	\707				(adapter->pool_res.max_rss_tables)708/* Max irqs avaialble for NIC */709#define be_max_irqs(adapter)		\710			(min_t(u16, be_max_nic_eqs(adapter), num_online_cpus()))711 712/* Max irqs *needed* for RX queues */713static inline u16 be_max_rx_irqs(struct be_adapter *adapter)714{715	/* If no RSS, need atleast one irq for def-RXQ */716	u16 num = max_t(u16, be_max_rss(adapter), 1);717 718	return min_t(u16, num, be_max_irqs(adapter));719}720 721/* Max irqs *needed* for TX queues */722static inline u16 be_max_tx_irqs(struct be_adapter *adapter)723{724	return min_t(u16, be_max_txqs(adapter), be_max_irqs(adapter));725}726 727/* Max irqs *needed* for combined queues */728static inline u16 be_max_qp_irqs(struct be_adapter *adapter)729{730	return min(be_max_tx_irqs(adapter), be_max_rx_irqs(adapter));731}732 733/* Max irqs *needed* for RX and TX queues together */734static inline u16 be_max_any_irqs(struct be_adapter *adapter)735{736	return max(be_max_tx_irqs(adapter), be_max_rx_irqs(adapter));737}738 739/* Is BE in pvid_tagging mode */740#define be_pvid_tagging_enabled(adapter)	(adapter->pvid)741 742/* Is BE in QNQ multi-channel mode */743#define be_is_qnq_mode(adapter)		(adapter->function_mode & QNQ_MODE)744 745#ifdef CONFIG_BE2NET_LANCER746#define lancer_chip(adapter)	(adapter->pdev->device == OC_DEVICE_ID3 || \747				 adapter->pdev->device == OC_DEVICE_ID4)748#else749#define lancer_chip(adapter)	(0)750#endif /* CONFIG_BE2NET_LANCER */751 752#ifdef CONFIG_BE2NET_SKYHAWK753#define skyhawk_chip(adapter)	(adapter->pdev->device == OC_DEVICE_ID5 || \754				 adapter->pdev->device == OC_DEVICE_ID6)755#else756#define skyhawk_chip(adapter)	(0)757#endif /* CONFIG_BE2NET_SKYHAWK */758 759#ifdef CONFIG_BE2NET_BE3760#define BE3_chip(adapter)	(adapter->pdev->device == BE_DEVICE_ID2 || \761				 adapter->pdev->device == OC_DEVICE_ID2)762#else763#define BE3_chip(adapter)	(0)764#endif /* CONFIG_BE2NET_BE3 */765 766#ifdef CONFIG_BE2NET_BE2767#define BE2_chip(adapter)	(adapter->pdev->device == BE_DEVICE_ID1 || \768				 adapter->pdev->device == OC_DEVICE_ID1)769#else770#define BE2_chip(adapter)	(0)771#endif /* CONFIG_BE2NET_BE2 */772 773#define BEx_chip(adapter)	(BE3_chip(adapter) || BE2_chip(adapter))774 775#define be_roce_supported(adapter)	(skyhawk_chip(adapter) && \776					(adapter->function_mode & RDMA_ENABLED))777 778extern const struct ethtool_ops be_ethtool_ops;779 780#define msix_enabled(adapter)		(adapter->num_msix_vec > 0)781#define num_irqs(adapter)		(msix_enabled(adapter) ?	\782						adapter->num_msix_vec : 1)783#define tx_stats(txo)			(&(txo)->stats)784#define rx_stats(rxo)			(&(rxo)->stats)785 786/* The default RXQ is the last RXQ */787#define default_rxo(adpt)		(&adpt->rx_obj[adpt->num_rx_qs - 1])788 789#define for_all_rx_queues(adapter, rxo, i)				\790	for (i = 0, rxo = &adapter->rx_obj[i]; i < adapter->num_rx_qs;	\791		i++, rxo++)792 793#define for_all_rss_queues(adapter, rxo, i)				\794	for (i = 0, rxo = &adapter->rx_obj[i]; i < adapter->num_rss_qs;	\795		i++, rxo++)796 797#define for_all_tx_queues(adapter, txo, i)				\798	for (i = 0, txo = &adapter->tx_obj[i]; i < adapter->num_tx_qs;	\799		i++, txo++)800 801#define for_all_evt_queues(adapter, eqo, i)				\802	for (i = 0, eqo = &adapter->eq_obj[i]; i < adapter->num_evt_qs; \803		i++, eqo++)804 805#define for_all_rx_queues_on_eq(adapter, eqo, rxo, i)			\806	for (i = eqo->idx, rxo = &adapter->rx_obj[i]; i < adapter->num_rx_qs;\807		 i += adapter->num_evt_qs, rxo += adapter->num_evt_qs)808 809#define for_all_tx_queues_on_eq(adapter, eqo, txo, i)			\810	for (i = eqo->idx, txo = &adapter->tx_obj[i]; i < adapter->num_tx_qs;\811		i += adapter->num_evt_qs, txo += adapter->num_evt_qs)812 813#define is_mcc_eqo(eqo)			(eqo->idx == 0)814#define mcc_eqo(adapter)		(&adapter->eq_obj[0])815 816#define PAGE_SHIFT_4K		12817#define PAGE_SIZE_4K		(1 << PAGE_SHIFT_4K)818 819/* Returns number of pages spanned by the data starting at the given addr */820#define PAGES_4K_SPANNED(_address, size) 				\821		((u32)((((size_t)(_address) & (PAGE_SIZE_4K - 1)) + 	\822			(size) + (PAGE_SIZE_4K - 1)) >> PAGE_SHIFT_4K))823 824/* Returns bit offset within a DWORD of a bitfield */825#define AMAP_BIT_OFFSET(_struct, field)  				\826		(((size_t)&(((_struct *)0)->field))%32)827 828/* Returns the bit mask of the field that is NOT shifted into location. */829static inline u32 amap_mask(u32 bitsize)830{831	return (bitsize == 32 ? 0xFFFFFFFF : (1 << bitsize) - 1);832}833 834static inline void835amap_set(void *ptr, u32 dw_offset, u32 mask, u32 offset, u32 value)836{837	u32 *dw = (u32 *) ptr + dw_offset;838	*dw &= ~(mask << offset);839	*dw |= (mask & value) << offset;840}841 842#define AMAP_SET_BITS(_struct, field, ptr, val)				\843		amap_set(ptr,						\844			offsetof(_struct, field)/32,			\845			amap_mask(sizeof(((_struct *)0)->field)),	\846			AMAP_BIT_OFFSET(_struct, field),		\847			val)848 849static inline u32 amap_get(void *ptr, u32 dw_offset, u32 mask, u32 offset)850{851	u32 *dw = (u32 *) ptr;852	return mask & (*(dw + dw_offset) >> offset);853}854 855#define AMAP_GET_BITS(_struct, field, ptr)				\856		amap_get(ptr,						\857			offsetof(_struct, field)/32,			\858			amap_mask(sizeof(((_struct *)0)->field)),	\859			AMAP_BIT_OFFSET(_struct, field))860 861#define GET_RX_COMPL_V0_BITS(field, ptr)				\862		AMAP_GET_BITS(struct amap_eth_rx_compl_v0, field, ptr)863 864#define GET_RX_COMPL_V1_BITS(field, ptr)				\865		AMAP_GET_BITS(struct amap_eth_rx_compl_v1, field, ptr)866 867#define GET_TX_COMPL_BITS(field, ptr)					\868		AMAP_GET_BITS(struct amap_eth_tx_compl, field, ptr)869 870#define SET_TX_WRB_HDR_BITS(field, ptr, val)				\871		AMAP_SET_BITS(struct amap_eth_hdr_wrb, field, ptr, val)872 873#define be_dws_cpu_to_le(wrb, len)	swap_dws(wrb, len)874#define be_dws_le_to_cpu(wrb, len)	swap_dws(wrb, len)875static inline void swap_dws(void *wrb, int len)876{877#ifdef __BIG_ENDIAN878	u32 *dw = wrb;879	BUG_ON(len % 4);880	do {881		*dw = cpu_to_le32(*dw);882		dw++;883		len -= 4;884	} while (len);885#endif				/* __BIG_ENDIAN */886}887 888#define be_cmd_status(status)		(status > 0 ? -EIO : status)889 890static inline u8 is_tcp_pkt(struct sk_buff *skb)891{892	u8 val = 0;893 894	if (ip_hdr(skb)->version == 4)895		val = (ip_hdr(skb)->protocol == IPPROTO_TCP);896	else if (ip_hdr(skb)->version == 6)897		val = (ipv6_hdr(skb)->nexthdr == NEXTHDR_TCP);898 899	return val;900}901 902static inline u8 is_udp_pkt(struct sk_buff *skb)903{904	u8 val = 0;905 906	if (ip_hdr(skb)->version == 4)907		val = (ip_hdr(skb)->protocol == IPPROTO_UDP);908	else if (ip_hdr(skb)->version == 6)909		val = (ipv6_hdr(skb)->nexthdr == NEXTHDR_UDP);910 911	return val;912}913 914static inline bool is_ipv4_pkt(struct sk_buff *skb)915{916	return skb->protocol == htons(ETH_P_IP) && ip_hdr(skb)->version == 4;917}918 919static inline bool is_ipv6_ext_hdr(struct sk_buff *skb)920{921	if (ip_hdr(skb)->version == 6)922		return ipv6_ext_hdr(ipv6_hdr(skb)->nexthdr);923	else924		return false;925}926 927#define be_error_recovering(adapter)	\928		(adapter->flags & BE_FLAGS_TRY_RECOVERY)929 930#define BE_ERROR_EEH		1931#define BE_ERROR_UE		BIT(1)932#define BE_ERROR_FW		BIT(2)933#define BE_ERROR_TX		BIT(3)934#define BE_ERROR_HW		(BE_ERROR_EEH | BE_ERROR_UE | BE_ERROR_TX)935#define BE_ERROR_ANY		(BE_ERROR_EEH | BE_ERROR_UE | BE_ERROR_FW | \936				 BE_ERROR_TX)937#define BE_CLEAR_ALL		0xFF938 939static inline u8 be_check_error(struct be_adapter *adapter, u32 err_type)940{941	return (adapter->err_flags & err_type);942}943 944static inline void be_set_error(struct be_adapter *adapter, int err_type)945{946	struct net_device *netdev = adapter->netdev;947 948	adapter->err_flags |= err_type;949	netif_carrier_off(netdev);950 951	dev_info(&adapter->pdev->dev, "%s: Link down\n", netdev->name);952}953 954static inline void  be_clear_error(struct be_adapter *adapter, int err_type)955{956	adapter->err_flags &= ~err_type;957}958 959static inline bool be_multi_rxq(const struct be_adapter *adapter)960{961	return adapter->num_rx_qs > 1;962}963 964void be_cq_notify(struct be_adapter *adapter, u16 qid, bool arm,965		  u16 num_popped);966void be_link_status_update(struct be_adapter *adapter, u8 link_status);967void be_parse_stats(struct be_adapter *adapter);968int be_load_fw(struct be_adapter *adapter, u8 *func);969bool be_pause_supported(struct be_adapter *adapter);970int be_update_queues(struct be_adapter *adapter);971int be_poll(struct napi_struct *napi, int budget);972void be_eqd_update(struct be_adapter *adapter, bool force_update);973 974/*975 * internal function to initialize-cleanup roce device.976 */977void be_roce_dev_add(struct be_adapter *);978void be_roce_dev_remove(struct be_adapter *);979 980/*981 * internal function to open-close roce device during ifup-ifdown.982 */983void be_roce_dev_shutdown(struct be_adapter *);984 985#endif				/* BE_H */986